- 5 -
CARE AND MAINTENANCE
Notice
Do not use harsh abrasives or caustic cleansers to clean fixture surface. A mild detergent, warm water, and a
softcloth will remove normal dirt and soap accumulations from fittings and surfaces. Rinse thoroughly after
cleaning and polish with a soft dry cloth to restore original luster of material.
Do not use cleansers in tank. Products containing chlorine (calcium hypochlorite) can seriously damage fittings
inthe tank. This damage can cause leakage and property damage.
Shall not be responsible or liable for any
tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite).
Using this guide and referring to the accompanying instructions should help you solve most
common problems encountered.
TROUBLE SHOOTING GUIDE
Problem
Possible Cause
To Correct
1. Poor flushing action
a. Water level in tank is below prescribelevel.
b. Flush valve mechanism in tank closes too quickly
or does not open.
c. Flush handle or button needs replacing.
d. Water pressure is too low.
e. Partially clogged trapway and / or drainpipe.
f. Cleanser used in tank deposits residue.
g. No air vent.
a. Set to prescribed level.
b. Make sure there are no any material stuck
to outlet components.
c. Replace.
d. Normal water supply pressure must be at least
20 psi.
e. Use a plunger or toilet augur to unclog.
f. Clean out tank and cease using the cleanser.
g. Install air vent per instructions.
2. Water won’t stop
running
a. Water level in tank is higher than overflow pipe.
o
t
s
e
u
n
i
t
n
o
c
r
e
t
a
w
f
I
.
y
l
p
p
u
s
r
e
t
a
w
e
h
t
f
f
o
n
r
u
T
.
b
flow into the bowl the flush valve seat and / or
rubber seal disk are worn or deforme d.
a. Adjust the cylinder to maintain the water at the
prescribed level.
b. Replace seat, rubber seal disk, or complete
assembly, as needed.
3. Water supply hose
leaks
a. Improper installation
b. Water pressure is too high.
a. Reinstall, according to instructions.
b. Water pressure must not exceed 80 psi.
c. Turn off the water supply valve. If water continues
to flow into the bowl until the water level falls to
y
a
m
s
i
r
b
e
d
r
o
d
n
a
s
,
e
p
i
p
w
o
l
f
r
e
v
o
e
h
t
f
o
l
e
v
e
l
e
h
t
be lodgeg in the water control mecha nism.
d. Flush valve string is too tight, holding the flush
valve open.
e. Button needs replacing.
c. Shut off water supply valve. Remove top cap
of water control. Clean and reassemble, or
replace plunger.
d. Replace fulsh valve unit.
e. Replace button.
Содержание 39320000
