Groen GSSP-BL-10G, Руководство по обслуживанию

Страница: 61 / 65

61 SM-GSSP BOILERLESS STEAMER
ERRORS
1:30:45
+1m
12:00pm
Timed
0:30
Pan Timers
Brussel Sprouts
5
SHUTDOWN H:MM:SS
1:30:45
+1m
12:00pm
Timed
0:30
Pan Timers
Brussel Sprouts
5
SHUTDOWN H:MM:SS
Error
Fatal
Error
Warning
Fatal error. Call for service.
888-994-7636
Silence Alarm
01 - High
Limit Exceeded
Cooling fan failed.
Check for blockage.
Okay
04 - Cooling
Fan Failure
ERROR FATAL
When a fatal error occurs, a pop up will be displayed and an alarm tone will
sound (continuous beep for 10 seconds, repeating every 60 seconds). If multiple
errors occur, only the last error will be displayed. All errors will be recorded in
the error log along with the status of each component. Upon fatal error, the unit
will immediately go into a shutdown process (to be defined for each type of fatal
error), but the error will remain on the screen until the power button is switched
off. If errors still exist at start up, unit will re-alarm. “Silence Alarm” button will
stop the audible alarm but leave the pop up on the screen. The Pop up will
contain the menu icon in the upper right corner of the pop up to allow access to
the Menu. If the screen sits inactive for 20 seconds or if the “X” button is pressed
from the Menu, the error pop up will return. If Service Mode is entered at start
up after a fatal error, unit will go to the Service Code screen and allow Service
functions to be performed. Certain fatal errors may allow for a user to perform a
limited action like Delime unit. If the power button is turned off prior to shutdown
process completing, the error popup will disappear and the shutdown screen will
be shown until shutdown is complete, and then the screen will go blank.
ERROR WARNING
When a non-fatal error occurs, a pop up will be displayed and an alarm tone will
sound (continuous beep for 10 seconds, repeating every 60 seconds). If multiple
errors occur, the last error will be displayed. Once it is cleared by pressing Okay
button, previous errors will be displayed sequentially. All errors will be recorded
in the error log along with the status of each component.
Okay Button - Silences and removes alarm pop up until power is cycled. If error
reoccurs after power cycle, pop up will reoccur.
Buttons and actions will vary with error type.
1:30:45
+1m
12:00pm
Timed
0:30
Pan Timers
Brussel Sprouts
5
SHUTDOWN H:MM:SS
1:30:45
+1m
12:00pm
Timed
0:30
Pan Timers
Brussel Sprouts
5
SHUTDOWN H:MM:SS
Error
Data Entry
Yes
No
Data Entry Error
Input appropriate text
based on error condition.
Warning
Door Open
Close door to resume
normal operation.
Okay
Door Open
WARNING DOOR OPEN
During cook, hold and delime modes, leaving door open for longer than 2 minutes
(default) will show pop up message and sound a continuous tone alarm. Pop up
will go away and alarm will silence by pressing the OK button or by shutting the
door. Counter will start again after pressing the OK button or reopening the door.
Open time will be settable in settings, Off, 2 min, 5 min, 10 min. Door open icon
will always show on screen regardless of alarm status.
1:30:45
+1m
12:00pm
Timed
0:30
Pan Timers
Brussel Sprouts
5
SHUTDOWN H:MM:SS
Warning
Low Probe Failure -
Delime Mode “Off”
Okay
After shutdown clean all
probes, drip cup and overflow
drains. Failure to do so may
not allow unit to restart.
H:MM:SS
01 - Clean Cavity
Unit Will Shutdown
When Clock Expires
WARNING LOW PROBE FAILURE
When the low probe stops functioning during a Timed, Manual and Hold mode,
this non-fatal error pop up will be displayed and an alarm tone will sound
(continuous beep for 10 seconds, repeating every 60 seconds) along with a
shutdown clock that counts down to 0 from 8 hours. Time is displayed in yellow
text in H:MM:SS format. Pop up reoccurs when 1 hour is left on the shutdown
clock with time displayed flashing in 3 sec. intervals. When 1 minute is left on
shutdown clock, time displayed will flash in 1 sec. intervals until expired. (The
text flashing will be same for the shutdown clock on all other screens).
Okay Button - Silences alarm and transitions to the previous screen before the
pop up occurred with the shutdown clock displayed. Shutdown clock will be
displayed on all screens after occurrence until time expires or power button is
pressed to turn the unit off. If probe error reoccurs after power cycle, a pop up
will display.