background image

-14-

Shop Fox

®

 Classic Fence

Correcting Mounting 

Hole Misalignment

If the front and back mounting holes do not line 
up with the existing holes in the table top, it 
will be necessary to drill additional holes using 
one of the three following methods. Drilling 
and tapping holes into the edge of the table, 
drilling through the edge of the table and 
securing the rail with long bolts, washers, and 
nuts, or drilling holes in the rail that align with 
the holes in the table top.

Drilling and Tapping Mounting Holes

1. 

Position  the  rails  flush  with  the  top  of  the 

table  saw  table,  and  with  the  left  end  of 

the rails even with the left edge of the table 

extension. 

2. 

Clamp  the  rails  to  the  table  saw  using  C-

clamps or bar clamps. 

3. 

Mark the mounting holes on the edge of the 

table. 

4. 

Remove the rail and center punch the middle 

of the outlined holes on the table edge. 

5. 

At  each  center  punch  location,  drill  a 

1

8

diameter starter hole, then drill a 

5

16

" hole 

using the bit supplied with the 

SHOP FOX

® 

Classic Fence.

6. 

Insert  the  included 

3

8

"-16  tap  in  a  tap 

wrench  if  one  is  available.  If  a  tap  wrench 

is  not  available  use  a  socket  and  ratchet 

wrench.

7. 

Carefully align the tap with the hole. Advance 

the tap half a turn, back it out half a turn, 

advance  another  half  turn,  etc.,  until  the 

tap  turns  freely  or  can  be  visually  seen  at 

the exit end of the hole. 

8. 

Back  the  tap  out  and  proceed  to  the  next 

hole.  It  is  not  necessary  to  use  cutting  oil 

when tapping cast iron.

9. 

Install the rails and the bolts.

Drilling Through-Holes

1. 

Position  the  rails  flush  with  the  top  of  the 

table  saw  table,  and  with  the  left  end  of 

the rails even with the left edge of the table 

extension. 

2. 

Clamp  the  rails  to  the  table  saw  using  C-

clamps or bar clamps. 

3. 

Mark the mounting holes on the edge of the 

table. 

4. 

Remove  the  rail,  and  center  punch  the 

middle of the outlined holes.

5. 

Drill  a 

7

16

"  hole  all  the  way  through  the 

table edge. Again, cutting oil should not be 

required, but be sure to use a relatively slow 

speed on the drill. 

6. 

Remove any chips or burrs around the edge 

of  the  hole  which  might  cause  the  rail  to 

mount crooked. 

7. 

Install the rails and long bolts and make sure 

that the nut is fully threaded on the bolt.

Drilling Holes In the Rails

1. 

Clamp the rails to the table. 

2. 

Using  a  try  square  and  pencil,  transfer  the 

location of the rail mounting hole onto the 

rails. 

3. 

Remove  the  rails,  and  center  punch  the 

middle of the outlined holes.  

4. 

Drill 

1

2

" holes in the rails that match the rail 

mounting holes in your table.  

5. 

Remove any chips or burrs around the edge 

of  the  hole  which  might  cause  the  rail  to 

mount crooked. 

6. 

Install the rails and bolts.

Содержание H6472


























Отзывы: