Grizzly G0894 Скачать руководство пользователя страница 36

Страница: 36 / 48

-34-

Model G0894 (Mfd. Since 05/19)

Review the troubleshooting procedures in this section if a problem develops with your machine. If you need
replacement parts or additional help with a procedure, call our Technical Support.

Note: Please gather the

serial number and manufacture date of your machine before calling.

SECTION 7: SERVICE

Troubleshooting

Motor & Electrical

Symptom

Possible Cause

Possible Solution

Machine does not
start, or power
supply breaker
immediately trips
after startup.

1. E-Stop button depressed/at fault.

2. Incorrect power supply voltage or circuit

size.

3. Power supply circuit breaker tripped or fuse

blown.

4. Computer board at fault.
5. Wiring broken, damaged, or disconnected.

6. Inverter/control box at fault.
7. Motor at fault.

1. Rotate E-Stop button head to reset. Replace if at

fault.

2. Ensure correct power supply voltage and circuit

size.

3. Ensure power supply circuit is not overloaded and is

free of shorts. Reset circuit breaker or replace fuse.

4. Inspect/replace if at fault.
5. Fix broken/damaged wires or disconnected/

corroded connections.

6. Inspect inverter/controller box; replace if at fault.
7. Test/repair/replace.

Machine stalls or is
underpowered.

1. Dull cutter or incorrect cutter type for task.

2. Machine undersized for task.
3. Spindle jammed.

4. Spindle motor overheated.
5. Incorrect power supply voltage or circuit

size.

1. Replace/sharpen cutter. Use proper cutter for

cutting task.

2. Use correct cutter/reduce feed rate or depth of cut.
3. Disconnect power. Turn spindle by hand to identify/

fix cause of jam.

4. Check coolant, fill reservoir (

Page 33).

5. Ensure correct power supply voltage and circuit

size.

Machine has
vibration or noisy
operation.

1. Incorrect feed rate, spindle speed, or cutter

type.

2. Cutter or spindle at fault.

3. Workpiece loose.
4. Bit chattering.

5.  Collet at fault.
6.  Machine not level.
7.  Spindle bearings at fault.

1. Use correct feed rate and spindle speed; use

different cutter.

2. Replace or sharpen cutter; tighten loose spindle;

replace defective spindle, collet, or spindle nut
(

Page 25).

3. Secure workpiece with clamps (

Page 26).

4. Replace/sharpen cutter; index cutter to workpiece;

use correct feed rate and spindle speed.

5. Replace collet.
6. Level machine (

Page 18).

7. Test by rotating spindle; rotational grinding/loose

shaft requires bearing replacement.

Содержание G0894

















































Результаты поиска

Содержание G0894

Отзывы:

Похожие инструкции для G0894

Бренды по названию

Популярные бренды

Grizzly G0894, Руководство пользователя

Результаты поиска

Содержание G0894

Отзывы:

Похожие инструкции для G0894

Бренды по названию

Популярные бренды