Grizzly G0890 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 60

background image

G0890/G0891 (Mfd. Since 06/19)

-41-

Using a Rotacator

Items Needed

Qty

Hex Wrenches 3mm, 4mm ..........................1 Ea.
Wrench or Socket 10mm .............................1 Ea.
Rotacator (see

Page 31) ................................... 1

To use a Rotacator:

1. DISCONNECT MACHINE FROM POWER!

2. Make sure knives are set to correct height

(refer to

Adjusting/Replacing Knives on

Page 27 for detailed instructions). If machine
is helical cutterhead, make sure all inserts
are properly installed (refer to

Rotating/

Replacing Cutterhead Inserts on Page 29
for detailed instructions).

3. Raise headstock at least 4" above table.

4. Remove top cover, belt cover, and gearbox

cover.

5. Using your Rotacator, find bottom dead cen-

ter (BDC) of any knife/insert edge by slowly
rocking cutterhead pulley back and forth,
then set Rotacator dial to "0" (see

Figure 43).

Figure 43. Example of using a Rotacator to find

BDC.

6. Move feed speed knob to neutral position to

allow infeed roller to freely rotate.

7. Keeping Rotacator dial at "0", position it

under right-hand side of infeed roller and find
BDC of a serrated edge by rocking infeed
roller back and forth.

Figure 44. Example of infeed roller bushing

block and height adjustment controls.

Roller

Bushing

Block

Jam Nut

& Set Screw

9. Repeat Steps 7–8 on left side of infeed roller.

10. Re-check both sides of infeed roller and, if

necessary, make further adjustments until
infeed roller height from side-to-side is 0.040"
below BDC of cutterhead knife, then retighten
both jam nuts.

11. Keeping same "0" reference on Rotacator

dial from

Step 5, repeat Steps 7–10 for out-

feed roller, but adjust it until it is 0.020" below
BDC of cutterhead knife.

8. Loosen jam nuts and use set screws on each

side of feed roller as shown to adjust height
of infeed roller bushing block until Rotacator
dial shows 0.040", which is the recommended
distance for infeed roller below cutterhead.

12. Re-install belt cover, top cover, and gearbox

cover.

«
...
41
42
43
44
45
...
»

Содержание G0890





























































Отзывы:

Нет отзывов

Похожие инструкции для G0890

Бренд: Jensen Страницы: 8

Бренд: Jensen Страницы: 7

Бренд: Wido Страницы: 16

Бренд: Curtis Страницы: 8

Бренд: Consonance Страницы: 7

Бренд: Goldmund Страницы: 13

Бренд: Sonic Frontiers Страницы: 8

inspiration C6m

Бренд: AVM Страницы: 16

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Powermatic Страницы: 2

Бренд: Powermatic Страницы: 40

Бренд: RCA Страницы: 19

Бренд: Metronome Страницы: 20

Бренд: CAMBRIDGE Страницы: 55

Бренд: DAS Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды