Grizzly G0776 Скачать руководство пользователя | Manualshive

Страница: 50 / 132

background image

-48-

Model G0776 (Mfd. Since 7/14)

Spider

Your lathe is equipped with a set of outboard
spindle supports otherwise known as a "spider"
(see

Figure 61).

Figure 61. Spider assembly located on the out-

board spindle.

Spider

Spindle Speed

Cutting Speed (FPM) x 12

*

Recommended

Dia. of Cut (in inches) x 3.14

Spindle

Speed
(RPM)

*

Double if using carbide cutting tool

=

Figure 62. Spindle speed formula for lathes.

Determining Spindle Speed

Using the correct spindle speed is important for
getting safe and satisfactory results, as well as
maximizing tool life.

To set the spindle speed for your operation, you
will need to: 1) Determine the best spindle speed
for the cutting task, and 2) Configure the lathe
controls to produce the required spindle speed.

Many variables affect the optimum spindle speed
to use for any given operation, but the two most
important are the recommended cutting speed for
the workpiece material and the diameter of the
workpiece, as noted in the formula shown below.

Cutting speed, typically defined in feet per minute
(FPM), is the speed at which the edge of a tool
moves across the material surface.

A recommended cutting speed is an ideal speed
for cutting a type of material in order to produce
the desired finish and optimize tool life.

The books

Machinery’s Handbook or Machine

Shop Practice, and some internet sites, pro-
vide excellent recommendations for which cutting
speeds to use when calculating the spindle speed.
These sources also provide a wealth of additional
information about the variables that affect cutting
speed and they are a good educational resource.

Also, there are a large number of easy-to-use
spindle speed calculators that can be found on
the internet. These sources will help you take into
account the applicable variables in order to deter-
mine the best spindle speed for the operation.

Remove spider screws when not in use.

Always DISCONNECT LATHE FROM POWER

when installing, removing, or adjusting spi-

der screws. Ignoring this warning can lead

to personal injury or machine damage.

The  spider  is  especially  designed  for  supporting
gun  barrels  during  chambering  operations;  how-
ever,  it  is  a  great  support  option  for  almost  any
long workpiece that extends through the outboard
side of the spindle.

The tips of the spider screws have brass wear
pads that hold the workpiece without causing
indents in the finish.

When spider screws are installed, always use the
jam  nuts  to  lock  each  spider  screw  in  position.
Merely  tightening  the  spider  screws  against  the
workpiece  and  leaving  the  jam  nuts  loose  is  not
safe. Spiders screws that loosen during operation
can crash into the lathe end cover.

Jam Nut

Spider Screw

«
...
48
49
50
51
52
...
»

Содержание G0776





































































































































Отзывы:

Нет отзывов

Похожие инструкции для G0776

Бренд: Lyman Страницы: 4

Бренд: Smithy Страницы: 39

Бренд: WoodFast Страницы: 14

PRO-FORME HOLLOWER

Бренд: woodcut Страницы: 12

Бренд: WoodFast Страницы: 15

Бренд: Bolton Tools Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды