Grizzly G0692 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 36

Grizzly G0692 Скачать руководство пользователя страница 24

-22-

Model G0692 (Mfg. 11/08 and Later)

SECTiON 6: MAiNTENANCE

Always disconnect power

to the machine before

performing maintenance.

failure to do this may

result in serious person-

al injury.

For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.

Daily Check:
•

loose mounting bolts/screws/nuts.

•

damaged or worn saw blade.

•

proper function of blade guard.

•

any other unsafe condition.

•

general cleanup to prevent buildup of metal
shavings.

Weekly Maintenance:
•

Clean the machine thoroughly.

•

Clean/grease the vise leadscrew.

Monthly Check:
•

Check/tighten all machine bolts.

Schedule

Cleaning the Model g0692 is relatively easy.
vacuum excess metal chips and wipe off the
remaining debris and residue with a dry cloth.

Cleaning

Keep unpainted cast iron surfaces rust-free with
regular applications of products like g96

®

gun

treatment, slipit

®

, or boeshield

®

t-9, all avail-

able through the grizzly catalog or website.

Unpainted Cast iron

vise Leadscrew

1. disConneCt saW FroM poWer!

2. use a rag to clean any debris from the vise

leadscrew.

3. apply multipurpose grease to the leadscrew

and completely open and close the vise sev-
eral times to distribute the grease.

Note: Periodically clean the leadscrew thor-
oughly with mineral spirits or other degreaser
and relubricate with multipurpose grease.

Lubrication

«
...
22
23
24
25
26
...
»

Содержание G0692





































Отзывы:

Нет отзывов