Grizzly G0692 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 36

Grizzly G0692 Скачать руководство пользователя страница 10

-8-

Model G0692 (Mfg. 11/08 and Later)

Safety instructions for Metal Cutting Saws

7. ATTENTiON TO WORK AREA. never

leave a machine running and unattended.
pay attention to the actions of others in the
area to avoid unintended accidents.

8. MAiNTENANCE/SERviCE. to reduce

the  risk  of  injury  from  accidental  startup,
all  inspections,  adjustments,  and  main-
tenance  are  to  be  done  with  the  power

off and the machine disconnected from
power. Wait for all moving parts to come
to a complete stop.

9. hEARiNG pROTECTiON & hAzARDS.

noise  generated  by  blade  and  workpiece
vibration,  material  handling,  and  power
transmission  can  cause  permanent  hear-
ing loss over time and interfere with com-
munication and audible signals.

10. hOT SURfACES. Contact with hot sur-

faces from machine components, ejec-
tions of hot chips, and the workpiece itself
can cause burns.

11. WORKpiECE hANDLiNG. always sup-

port the workpiece with table, vise, or
some type of support fixture to maintain
control over the workpiece during the cut.
Flag long pieces to avoid a tripping hazard.
never hold the workpiece with your hands
during a cut.

1. bLADE CONDiTiON. do not operate with

a dull, cracked or badly worn blade. a dam-
aged blade could break apart during use,
resulting in serious personal injury. inspect
blades for cracks and missing teeth before
each use.

2. hAND pLACEMENT. never position fin-

gers or thumbs in line with the cut.

hands

could be crushed in vise or from falling
machine components.

3. ENTANGLEMENT hAzARDS. do not

operate this saw without blade guard in
place. loose clothing, jewelry, long hair
and work gloves can be drawn into working
parts.

4. bLADE REpLACEMENT. When replac-

ing blades, disconnect the machine from
power to reduce the risk of injury from acci-
dental startup.

5. LOSS Of STAbiLiTY. unsupported

workpieces may jeopardize machine sta-
bility and cause the machine to tip and fall
which could cause serious injury.

6. fiRE hAzARD. if cutting magnesium, do

not allow magnesium chips to build up.
Magnesium chips are extremely flammable
and can catch fire and burn at very high
temperatures

No list of safety guidelines can be complete. Every shop environment is different. Like all

machines there is danger associated with the Model G0692. Accidents are frequently caused by

lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen

the possibility of operator injury. if normal safety precautions are overlooked or ignored, serious

personal injury may occur.

«
...
8
9
10
11
12
...
»

Содержание G0692





































Отзывы:

Нет отзывов