Grizzly EXTREME G0513X2 Скачать руководство пользователя

Страница: 17 / 100

G0513 Series Bandsaws (Mfd. Since 08/22)

-15-

Inventory

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.

If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.

Inventory (Figures 7–8) Qty

A. Bandsaw (not shown) ................................. 1

B. Table ........................................................... 1

C. Miter Gauge ................................................ 1

D. Rear Rail .................................................... 1

E. Fence Assembly ......................................... 1

F. Guide Post Handwheel............................... 1

G. Front Rail .................................................... 1

Hardware & Tools (Not Shown)

Qty

•

Flat Washers 8mm (Table) ......................... 4

•

Lock Washers 8mm (Table) ....................... 4

•

Hex Bolts M8-1.25 x 16 (Table) .................. 4

•

Hex Bolt M8-1.25 x 90 (Positive Stop) ........ 1

•

Hex Nuts M8-1.25 (Positive Stop, Fence)... 2

•

Cap Screws M6-1 x 16 (Fence) .................. 2

•

Hex Bolts M6-1 x 20 (Fence) ...................... 2

•

Lock Washers 6mm (Fence) ...................... 2

•

Flat Washers 6mm (Fence) ........................ 2

•

Hex Nut M6-1 (Fence) ................................ 1

•

Table Pin..................................................... 1

•

Table Insert ................................................. 1

•

Fence Handle M8-1.25 x 22 (Fence) .......... 1

•

Rail Pad M6-1 x 18 (Fence) ........................ 1

•

Hex Wrenches 5, 8mm ......................1 Each

•

Open-End Wrench 10 x 13mm ................... 1

Figure 8. Fence components and handwheel.

Figure 7. Table and miter gauge.

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

G0513

Содержание EXTREME G0513X2





































































































Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Похожие инструкции для EXTREME G0513X2

Бренды по названию

Популярные бренды

Grizzly EXTREME G0513X2, Руководство пользователя

Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Похожие инструкции для EXTREME G0513X2

Бренды по названию

Популярные бренды