114
CZ
• Síťový kabel vždy táhněte za sebou a
po obrácení jej položte na již poseka
-
nou stranu.
• S přístrojem pracujte jen při krokové
rychlosti a veďte jej tak, abyste tvořili
co nejrovnější pásy. K úplnému pose
-
kání by se jednotlivé pásy měly vždy o
několik centimetrů překrývat.
• Řeznou hloubku nastavte tak, aby
nebyl přístroj přetížen. V opačném
případě může být poškozen motor.
• Na svazích vždy pracujte příčně ke
svahu. Buďte velmi opatrní při postu
-
pu směrem zpět a tažení přístroje.
• Po každém použití přístroj vyčistěte, viz
kapitolu „Čištění, údržba, skladování“.
Po práci a k přemístění přístroj vy
-
pněte, vytáhněte síťovou zástrčku
a počkejte, až se nůž zastaví. Hro
-
zí nebezpečí poranění osob.
Čištění/údržba/skladování
Práce, které nejsou uvedeny v
tomto návodu, mohou provádět
jen námi zmocněná servisní
střediska. Používejte jen origi
-
nální díly.
Při manipulaci s nožem noste
ochranné rukavice.
Před jakoukoli údržbou a čištěním
přístroj vypněte, vytáhněte síťovou
zástrčku ze zásuvky a počkejte, až
se nůž úplně zastaví. Hrozí nebez
-
pečí poranění osob.
Všeobecné práce k čištění
a údržbě
Sekačku neostřikujte vodou.
Hrozí nebezpečí úrazu elektric
-
kým proudem.
• Přístroj stále udržujte v čistotě. K čiš
-
tění použijte kartáč nebo utěrku, ale
žádné čisticí prostředky popř. rozpou
-
štědla.
• Po sekání kusem dřeva nebo plastu
odstraňte ulpělé zbytky rostlin z kol,
větracích otvorů, vyhazovacího otvoru
a oblasti nože. Nepoužívejte tvrdé
nebo špičaté předměty, mohly by po
-
škodit přístroj.
• Občas naolelujte kola.
• Před každým použitím zkontrolujte,
zda sekačka nevykazuje viditelné zá
-
vady, jako např. volné, opotřebované
nebo poškozené díly. Zkontrolujte pev
-
né utažení šroubů, matic a svorníků.
• Zkontrolujte, zda nejsou poškozeny,
a zda jsou správně umístěny kryty a
ochranná zařízení. V případě potřeby
je vyměňte.
Výměna nože
Je-li nůž tupý, tak by jej měl nabrousit od
-
borný servis. Je-li nůž poškozený nebo se
zdá nevyvážený, tak musí být vyměněn
(viz kapitolu Náhradní díly).
1. Otočte přístroj.
2. Použijte silné rukavice a přidržte
nůž (25). Pomocí klíče na šrou
-
by odšroubujte ve směru proti
chodu hodinových ručiček šroub
nože (26) z motorového vřetena.
3. Nový nůž namontujte v opač
-
ném pořadí. Dbejte na správ
-
nou polohu nože a šroub pevně
utáhněte.
Skladování
Aby přístroj nezabíral tolik místa,
odblokujte 2 upínací páčky (2) a
sklopte rámovou rukojeť (1). Dbejte,
aby nedošlo ke skřípnutí kabelu.
Содержание ERM 1435 G
