background image

t20568 1

1

4

" brad nailer

-3

-

operating  this  nailer  can  propel 
objects  into  the  air,  causing  imme-
diate  eye  damage.  to  protect  your-
self,  always  wear  american  national 
standards  institute  (ansi)  approved 
safety glasses or goggles when oper-
ating this equipment. in addition, the 
intensity of sound made by this nailer 
at  discharge  can  reach  90  decibels. 
to protect your hearing, always wear 
ansi  approved  ear  protection  when 
operating this nailer.

never  point  this  nailer  at  yourself  or 
another  person!  always  pay  attention 
to  the  direction  this  nailer  is  pointed. 
use this tool with respect and caution 
to lessen the possibility of operator or 
bystander injury. ignoring this warning 
may result in serious personal injury.

nailer  accidents  routinely  happen 

while  moving  the  gun  to  another 

location,  such  as  up  ladders,  to 

another  room,  or  even  another  job 

site.  always  disconnect  the  gun 

immediately  after  use  and  never 

transport the gun while connected to 

the air—even if the air compressor is 

disconnected from its power source!

no list of safety guidelines can be 

complete. every shop environment 

is different. always consider safety 

first, as it applies to your individual 

working conditions. use this and 

other tools with caution and respect. 

failure to do so could result in seri-

ous personal injury, damage to 

equipment or poor work results.

read  the  manual  before  operation. 
become  familiar  with  these  nailers, 
their  safety  instructions,  and  opera-
tion  before  beginning  any  work. 
serious  personal  injury  may  result  if 
safety  or  operational  information  is 
not understood or followed. 

Содержание 1 1/4" Brad Nailer T20568





















Отзывы: