background image

Page 2

Model LCD-2R and LCD-2A

Introduction

The Grindmaster-Cecilware Liquid Coffee Dispensers (LCD-2A) and the Liquid Coffee Chilled Dispenser

(LCD-2R) deliver two types of coffee made from liquid concentrate plus hot water. 

• The dispenser can be set up for continuous draw (by the cup) for self-serve applications, or portion-control 

to fill carafes and decanters for wait staff. The standard machine allows for (2) portion sizes per dispense 

head with the use of a hidden override switch located on the bottom left side of the door. If the override 

switch is pushed, the user has (10) seconds to activate a switch to achieve the override portion setting 

programmed for that dispense head. Optionally, the machine can be fitted with 2 portion touchpads.

• Follow the concentrate manufacturer’s storage and shelf life recommendations. Product flavor profile is 

extended with chilled product storage cabinet featured in the LCD-2R.

• The refrigerated model LCD-2R incorporates a Solid State Thermoelectric cooling system which requires 

little maintenance. Cleaning of the thermoelectric may be required on a periodic basis depending on the air 

quality of the loaction and should be performed only by a qualified technician.

• This dispenser is designed to operate when the ambient temperatures are from 32°F (0°C) minimum to 

86°F (30°C) maximum. Do not allow machine to operate or be stored below freezing temperatures or 

permanent damage will occur to machine unless water has been purged from all water lines.

Содержание LCD-2A Operation and





















Отзывы: