Grieve Furnaces Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 36

background image

W:\ELECTRICAL\INSTRUCT\FURNACE\FURNACE GENERAL INSTRUCTIONS 2011.DOC

30 of 36

01/2014

10 APPENDIX B - REFERENCES

The following sources of additional information are provided for reference in these
instructions. This is not presented as a complete list of all possible reference sources.

10.1 Factory Mutual Engineering Corporation

1151 Boston-Providence Turnpike
P.O. Box 9102
Norwood, Massachusetts 02062
Attn: Publications Order Processing

Specifications 6-9, Industrial Ovens and Dryers

10.2 National Fire Protection Association

One Batterymarch Park
Quincy, Massachusetts 02209-9101

Most current issue of:

NFPA 86 - Ovens and Furnaces
NFPA 70 - National Electric Code
NFPA 54 - National Fuel Gas Code
NFPA 10 - Standard for Portable Fire Extinguishers
NFPA 11 - Standard for Low-Expansion Foam
NFPA 12 - Standard on Carbon Dioxide Extinguishing Systems
NFPA 13 - Standard for the Installation of Sprinkler Systems
NFPA 14 - Standard for the Installation of Standpipe and Hose Systems
NFPA 15 - Standard for Water Spray Fixed Systems for Fire Protection
NFPA 17 - Standard for Dry Chemical Extinguishing Systems
NFPA 17A-Standard for Wet Chemical Extinguishing Systems
NFPA 25 - Standard for the Inspection, Testing and Maintenance of Water-Based

Fire Protection Systems

NFPA 30 - Flammable and Combustible Liquids Code
NFPA 31 - Standard for the Installation of Oil-Burning Equipment
NFPA 34 - Standard for Dipping and Coating Processes Using Flammable or

Combustible Liquids

NFPA 58 - Liquified Petroleum Gas Code
NFPA 79 - Electrical Standard for Industrial Machinery
NFPA 91 - Standard for Exhaust Systems for Air Conveying of Vapors, Gases, Mists

and Noncombustible Particulate Solids

10.3 ASME Publications

American Society of Mechanical Engineers
345 East 47

th

Street

New York, NY 10017

The most current issue of:
ASME Boiler and Pressure Vessel Code
ASME B31.1 - Power Piping
ASME B31.3 - Process Piping

10.4 ANSI Publications:

American National Standards Institute
11 West 42

nd

Street, 13

th

Floor

New York, NY 10036

The most current issues of:
ANSI Z117-1 - Safety Requirements for Confined Spaces

«
...
28
29
30
31
32
...
»

Содержание Furnaces





































Отзывы:

Нет отзывов

Похожие инструкции для Furnaces

Бренд: Barnstead Страницы: 33

Бренд: Barnstead Страницы: 48

Бренд: baltur Страницы: 53

Бренд: ICP Страницы: 10

Бренд: Amana Страницы: 20

Бренд: Bryant Страницы: 8

Бренд: Carrier Страницы: 66

Бренд: Fire Chief Страницы: 20

Бренд: Coleman Страницы: 8

Бренд: Coleman Страницы: 12

Бренд: Fedders Страницы: 50

Бренд: Day and Night Страницы: 12

Бренд: York Страницы: 4

Бренд: York Страницы: 4

Бренд: ICP Страницы: 33

PLB-098 LOW-BOY

Бренд: Williamson-Thermoflo Страницы: 26

PxXD-G9V-DH series

Бренд: Coleman Страницы: 40

Бренд: American Standard Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды