background image

Page  4

The alarm on delay defaults to 5" (seconds). It can be changed from 1-59" 

(seconds) and 1-10' (minutes) using <UP> or <DOWN>.

<MENU> 

Press to advance to next menu item

9. ALARM DELAY

The alarm off delay defaults to 5" (seconds). It can be changed from 1-59" 

(seconds) and 1-10' (minutes) using <UP> or <DOWN>.

<MENU> 

Press to advance to next menu item

10. ALARM DELAY

MENU

OFF MENU

The alarm test defaults to OFF. It can be set to On using <UP> or <DOWN>. This 

forces the relay to activate.

<MENU> 

Press to advance to next menu item

11. ALARM TEST

MENU

8. ALARM TEST

The low pressure alarm limit defaults to about 25% of the range. This equals - 0.50 

for the ± 1 "wc range, - 130 for the ± 250 Pa range, etc. It can be changed using 

<UP> or <DOWN> throughout the range. Resolution for each range is: ± 1 "wc 

(0.05), ± 0.25 "wc (0.01), ± 250 Pa (10) and ± 60 Pa (2). Note that the ± 250 Pa range 

must be displayed as /10 such that it is - 25H to 25H.

<MENU> 

Press to advance to next menu item

MENU "WC

The high pressure alarm limit defaults to about 75% of the range. This  

0.50 for the ± 1 "wc range, + 130 for the ± 250 Pa range, etc. It can be changed 

using <UP> or <DOWN> throughout the range. Resolution for each range is: ± 1 

"wc (0.05), ± 0.25 "wc (0.01), ± 250 Pa (10) and ± 60 Pa (2). Note that the ± 250 Pa 

range must be displayed as /10 such that it is - 25H to 25H.

7. HIGH PRESSURE ALARM

<MENU> 

Press to advance to next menu item

MENU "WC

<MENU> 

Press to advance to next menu item

<MENU> 

Press to advance to next menu item

The pressure averaging time defaults to 5" (seconds). This can be changed from 

1-60" (seconds) using <UP> or <DOWN>.

5. PRESSURE AVERAGING

MENU

Only if a relay is installed. 

The alarm enable/disable defaults to enable (On). The 

alarm can be disabled here. Use <UP> or <DOWN> to disable (OFF) the alarm. If 

the alarm is disabled no alarm condition will be set. Note if the alarm is disabled, 

then none of the alarm menu settings will be shown in the menu. Use <MENU> to 

save and advance.

6. ALARM

<MENU> 

Press to advance to next menu item

MENU

IN-GE-UPXXX-01 07/20

Copyright © Greystone Energy Systems, Inc.   All Rights Reserved    Phone:  +1 506 853 3057  Web: www.greystoneenergy.com

Содержание UP Series







Отзывы: