manualshive.com logo in svg

GreenWorks 20212, Руководство пользователя

Поделиться
Скачать
GreenWorks 20212 Скачать руководство пользователя страница 21

21

MAINTENANCE

REPLACING THE BAR AND CHAIN

 

(See Figure 16-19)

W A R N I N G

To avoid possible serious injury, stop the motor and remove the battery from the pole saw 
before replacing the bar, chain, or performing any maintenance operation. 

 Remove the lock bolt and drivecase cover.

 The bar contains a bar stud slot that fits over the bar stud. The bar also contains a chain 

 

pin hole.

 Fit the chain over the sprocket and into the bar groove. The cutters on the top of the bar 

should face toward the bar tip, in the direction of the chain rotation.

 

bar must be free to move for tension adjustment.

 Remove all slack from chain by turning the chain tensioning screw clockwise, assuring that 

the chain seats into the bar groove during tensioning.

 Lift the tip of the bar up to check for sag. Release the tip of the bar, and turn the chain 

tensioning screw 1/2 turn clockwise.

 Repeat this process until sag does not exist.

 Hold the tip of the bar up and tighten the lock bolt securely.

 Chain is correctly tensioned when there is no slack on the underside of the bar, the chain is 

snug, but it can be turned by hand without binding.

NOTE: If chain is too tight, it will not rotate. Loosen the bar nut slightly and turn adjusting screw 1/4 turn coun-
terclockwise. Lift the tip of the bar up and retighten lock bolt.

Fig. 16

Fig. 17

Fig. 19

Fig. 18

Drivecase
Cover 

Chain
Tensioning Pin

Bar Stud

Bar Stud Slot

Lock Bolt

Chain
Tensioning
Pin Hole

Sprocket

Lock Bolt

Chain Rotation

Sprocket

Chain 

BAR

Chain Tensioning 
Screw

Drivecase
Cover 

Chain 

Bar

Lock 
Bolt

Содержание 20212

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды