background image

Greenlee Tools, Inc.

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

10

EK1230LX and EK1230CLX Crimping Tools 

Maintenance

Wear eye protection when operating 

or servicing this tool. 
Failure to wear eye protection could 

result in serious eye injury from flying 

debris or hydraulic oil. 

Skin injection hazard:
Do not use hands to check for oil 

leaks. Oil under pressure easily punc-

tures skin. If injured, seek medical 

attention immediately to remove oil.
Failure to observe this warning could 

result in serious injury, gangrene, or 

death.

Do not use solvents or flammable 

liquids to clean the tool body. 

Solvents or flammable liquids could 

ignite and cause serious injury or 

property damage.

Pinch points:
•  Remove battery before changing 

dies, adapters, or jaws.

•  Keep hands away from the crimp-

ing tool head when crimping.

Failure to observe these warnings 

could result in severe injury or death.

Relief valve adjustments must be done by an  

authorized service center.

Daily

Before use:

1.  Inspect the tool for wear or damage, such as cracks, 

gouges, or chips.

2.  Inspect the tool for damage or leaks.
3.  Inspect the rotation of the head assembly. Fully 

retract the ram. The head should rotate no more 

than 360°. If damage is detected, contact Greenlee 

customer service at 800-435-0786 for warranty 

service or repair.

After use:

1.  Use a damp cloth and mild detergent to clean the 

housing. Allow the housing to dry.

2.  Fully retract the ram. Place the tool in the carrying 

case and store in a cool, dry place.

3.  If necessary, recharge the batteries. Refer to the 

instructions supplied with the battery charger.

Monthly

Thoroughly clean all surfaces.

Annually or After 10,000 Crimps

Contact Greenlee customer service at 800-435-0786 for 

warranty service or repair, and  hydraulic oil replacement.

Содержание GATOR EK1230CLX













Отзывы: