background image

Remote Cable Cutter

52087760 REV 1 

14

© 2021 Greenlee Tools, Inc.

Figure 4

Operation

1.  After selecting the Remote profile, secure the tool 

trigger in depressed position by moving the trigger 

ring over it.

2.  Click the toggle switch on the remote, the blue LED 

will start blinking.

3.  When the ID of the remote appears on the screen, 

confirm “Yes” by pressing the button on the tool 

next to it. The ID of the remote is found above the 

remote’s signal decal.

4.  When prompted by the tool screen, complete 

remote pairing by clicking the toggle switch, the 

blue LED on the remote will turn solid once a 

connection is made.

5.  Double click Extend on toggle switch to activate 

remote operation. (Fig. 2)

BTC3GL

Extend

Toggle Switch 

Retract

Figure 2

6.  Test the tool by double clicking the remote again 

and holding Extend on the toggle switch to advance 

the blade to test the wireless connection to the tool. 

The green LED on the remote will start blinking and 

stay blinking while the tool blade is moving.

7.  Single click and hold Retract on the toggle switch or 

press red Retract Button on tool to return blade to 

starting position.

8.  Open head by using the pull pin. (Figure 1)
9.  Position the tool so the cable is in the open cutting 

head. (Figure 1)

10.  Close Cutting Head and fully insert Pull Pin. Partial 

Pin insertion can cause a bad cut.

11.  Set up the tool at a 90-degree angle to cable  

(Figure 3) to ensure a straight cut, making sure the 

area is clear. Secure tool to limit shifting and twisting 

during operation and to keep tool from falling during 

operation.

Figure 3

12.  Move away from the cutter and to the area identified 

outside of potential arc flash range. (Figure 4)

13.   Double click and hold “Extend” on toggle switch, 

the green LED will start blinking. When the cut is 

complete, both the blue and green LEDs will be 

solid and an audible sound will be heard from the 

remote. The cutting process can be interrupted at 

any time by releasing the toggle and the blade can 

be retracted by pressing and holding “Retract” on 

toggle switch. 

14.  After the remote signals the cut is complete, move 

to retrieve the tool checking the area around the tool 

before moving closer to the tool. If the operator was 

located out of sight while using the remote, the area 

may now have new hazards as a result of cutting 

the cable.

15.  Remove the battery before setting up for another 

cut or placing tool in storage

Note: The tool will automatically shut down after 30 

min of idleness when in Remote mode. A countdown 

will show on the OLED screen and will reset when the 

remote is used or disconnected.

Содержание ESG65LXR



















Отзывы: