Greenheck Vektor-HS Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

background image

Laboratory Exhaust System

6

®

Option 1:

• No isolation damper in roof curb
• Bottom inlet on bypass air plenum

Duct Installation

Bottom Inlet Duct Connection

The end of the duct (customer-supplied) is secured between the roof curb’s top edge and the curb cap of either the
Vektor-H or bypass air plenum. If an isolation damper is present in the roof curb, the duct is located between the
roof curb and the damper adapter tray.

Duct Connection to Curb

Side or End Duct Connection

• Vektor-H or Vektor-HS
• With bypass air plenum

NOTE

Plenum is provided with removable side or end
panels, allowing the proper duct connection.

Duct to Bypass Air Plenum

Bypass Air

Plenum

Weatherhood

Duct flange and

gasketing by

others

Roof Curb

Option 2:

• With isolation damper in roof curb

Vektor-H

Isolation Damper

Adapter Tray

Duct

Vektor-H or Vektor-HS

Duct

Roof Curb

«
...
4
5
6
7
8
...
»

Содержание Vektor-HS

















Отзывы:

Нет отзывов

Похожие инструкции для Vektor-HS

Бренд: jablotron Страницы: 48

Бренд: Fantech Страницы: 20

Бренд: HAMPTON BAY Страницы: 31

52" Canfield Pro

Бренд: Kichler Lighting Страницы: 15

Бренд: Faro Barcelona Страницы: 12

Бренд: Harbor Breeze Страницы: 20

Бренд: Maico Страницы: 28

Бренд: Parrot Uncle Страницы: 4

Pelham HVFC# 2299

Бренд: hudson valley Страницы: 12

Бренд: ebm-papst Страницы: 11

ARCHIVE LP3071 Series

Бренд: Fanimation Страницы: 38

Бренд: S&P Страницы: 20

Бренд: Levante Страницы: 4

Бренд: Bionaire Страницы: 2

Бренд: Fanco Страницы: 12

breez Slim SLM100

Бренд: Delta Страницы: 4

Бренд: impress Страницы: 14

Бренд: BENRUBI Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды