background image

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, 
install, operate or maintain the product described. Protect yourself and others by observing all safety 
information. Failure to comply with instructions could result in personal injury and/or property damage!

1

Electric Duct Heaters

These instructions apply to installation of duct heaters for zero clearance installation in ducts. They are approved 
for use with heat pumps, air conditioners, or other forced air systems and may be controlled by contactors, relays, 
sequencers, or solid state devices.
The duct heaters are pre-wired, have voltage ratings of 600 volts, both single phase and three phase. The duct 
heaters are furnished with integral controls.

Receiving and Handling

Upon receiving dampers, check for both obvious 
and hidden damage. If damage is found, record all 
necessary information on the bill of lading and file 
a claim with the final carrier. Check to be sure that 
all parts of the shipment, including accessories, are 
accounted for.
Dampers must be kept dry and clean. Indoor storage 
and protection from dirt, dust and the weather is 
highly recommended. Do not store at temperatures in 
excess of 100°F (38°C).

This manual is the property of the owner and is required for future maintenance. Please leave it with the owner when 
the jobs is complete.

Safety Warning

Improper installation, adjustment, alteration, service 
or maintenance can cause property damage, injury 
or death. Read the installation, operating, and 
maintenance instructions thoroughly before installing 
or servicing this equipment.

Table of Contents

General Information  ......................................2
Installation  ....................................................2
Electrical Requirements .................................3
Minimum Air Velocities ..................................3
Insulated Duct Installations  ..........................4
 Installation Details with SSR or Electronic 
Step Controllers   ..........................................5
Troubleshooting Guide ...............................6-8

®

Document  Number 478052 

IDHB & IDHC

Duct Heaters

Содержание IDHB









Отзывы: