background image

Installation, Operation and Maintenance Instructions

Safety Warning:

 

Improper installation, adjustment, alteration, service 
or maintenance can cause property damage, injury or 
death. Read the installation, operating, and maintenance 
instructions thoroughly before installing or servicing this 
equipment.

This manual is the property of the owner, and is required for future maintenance. Please leave it with the owner when the 
job is complete.

Warranty

Greenheck warrants this equipment to be free from 
defects in material and workmanship for a period of one 
year from the purchase date. Any units or parts which 
prove to be defective during the warranty period will be 
repaired or replaced at our option. Greenheck shall not 
be liable for damages resulting from misapplication or 
misuse of its products. Greenheck will not be responsible 
for any installation or removal costs. Greenheck will not 
be responsible for any service work or backcharges 
without prior written authorization. 

Due to continuing research, Greenheck reserves the right to change specifications without notice.

“UL CLASSIFIED (see complete marking on 

product)”

“UL CLASSIFIED to Canadian safety standards 

(see complete marking on product)”

 

UL Standard 555 & 555S (Classification R13317)

FSD-3XXV Series Dampers are intended for installation 

in accordance with combination fire smoke damper 

requirements established by:

National Fire Protection Association  
 

NFPA Standards 80, 90A, 92A, 92B, 101, & 105

IBC

 International Building Codes

New York City 

(MEA listing #260-91-M)

California State Fire Marshal 

 

Listing #3225-0981:103 and 3230-0981:104

Receiving and Handling

Upon receiving dampers, check for both obvious and 
hidden damage. If damage is found, record all necessary 
information on the bill of lading and file a claim with 
the final carrier. Check to be sure that all parts of the 
shipment, including accessories, are accounted for.
Dampers must be kept dry and clean. Indoor storage 
and protection from dirt, dust and the weather is highly 
recommended. Do not store at temperatures in excess of 
100°F (38°C).

Typical 
Actuator

RRL Control 
Device Standard

Document Number 461666 

FSD-3XXV Series 

1 1/2 Hour

Combination Fire Smoke Dampers 

(with factory installed sleeve and actuator) 

Vertical Blade

Installation Supplements

Refer to the appropriate Greenheck installation supplements 
for special requirements:
 

• Concrete Floor with Steel Deck

 

• Drive Slip Breakaway Connection

 

• Field Installed Sleeve

 

• Fire Resistant Ventilated Duct Assembly

 

• Firestop Material

 

• Greenheck Test Switch

 

• Grille Installation

 

• Metal Stud in Shaftwall

 

• No Flow Smoke Detector

 

• Open or Close Indicator

 

• Quick Connect Breakaway Connections

 

• Resettable Link

 

• Sealant Supplement

 

• Single Side Retaining Angle

 

• Single 3-Sided Retaining Angle

 

• Sleeve Extension

 

• Smoke Detector

 

• Tunnel Corridor

®

Содержание FSD-311V









Отзывы: