Greenheck DFD Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 52

background image

“Duct Continues”

Horizontal or Vertical Mount

Figure 1: Installation configurations for Grille access combination fire smoke dampers.

“Duct Terminates” Metal Stud

Vertical Mount

3/4 in. 14 ga.
Flange

#10 2 in. long sheet metal
screws spaced 6 in. on
center and maximum of 2 in.
from the corners, (minimum
of 2 screws per side),
through the sleeve into the
header, sill and jamb framing
members. Screw into rear
portion of the studs so as to
avoid space conflicts with
grille assembly.

Grille
(supplied
by others)

Combination Fire
Smoke Damper

3 1/2 in.

Max.

Thermal Blanket

On continuous duct installations, the retaining angles
must overlap the wall/floor by 1 in. (25mm). Because no
clearances are required between the wall/floor opening
and the sleeve, dampers may not be installed in the
plane of the wall using this installation method.

3. DUCT TO SLEEVE CONNECTIONS

Dampers are supplied with actuators (on applicable
models) and sleeves from the factory and can be
installed without the need for additional field installed
sleeves.
Sleeve gauges of 16 or 14 (1.5mm - 2mm) are to be
used. UL Standard 555 requires all ducts to terminate at
fire damper sleeves. Sleeve thickness must not be less
than the gauge of the connecting duct.
Duct to sleeve breakaway connections must be of the

type described on page

10

. Factory furnished round

duct

collars on type R and CR dampers are also

considered

to be breakaway connections and may be

used.

Factory Supplied
Thermal Blanket

3 1/2 in.

Max.

Combination fire
smoke damper

Masonry
floor

4. SECURING THE DAMPER/SLEEVE ASSEMBLY TO

WALL OPENINGS.

Damper/sleeve assemblies must be installed in wall
openings using flanges and sheet metal screws as
illustrated and described below.
• Flange on front (grille end) of sleeve must be a minimum

of 14 gauge (2mm) steel and have a 3/4 in. (19mm)
minimum flange leg (refer to

Figure 2

). Using #10

(19mm) sheet metal screws, screw from inside of sleeve
through the rear portion of the studs (as shown in

Figure 1

). Space screws a maximum of 6 in. (152mm)

on center and a maximum of 2 in. (51mm) from the
corners (minimum of 2 screws per side). No retaining
angles are required on the side of wall opposite from the
grille.

45

«
...
43
44
45
46
47
...
»

Содержание DFD Series





















































Отзывы:

Нет отзывов

Похожие инструкции для DFD Series

Бренд: BAC Страницы: 30

Бренд: Panasonic Страницы: 145

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 56

Therapy Air Smart TAS-100

Бренд: Zepter Страницы: 9

Бренд: EarthLinked Страницы: 16

Бренд: PremierOne Страницы: 7

Бренд: Kaysun Страницы: 16

Бренд: Oceanic Страницы: 67

Бренд: Aerial Страницы: 32

Бренд: Eco Air Страницы: 16

Бренд: JAP Страницы: 48

Бренд: INVENTOR Страницы: 54

Бренд: Vintage Air Страницы: 12

Бренд: Hisense Страницы: 14

Air Purification System I-6500 A-HO

Бренд: AllerAir Страницы: 1

Ciatronic DD 100

Бренд: CIAT Страницы: 24

Бренд: Klimaire Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды