background image

Single Sided Angle Method:

 For single side installations the retaining angles must be attached to the wall/floor  

(see 

Figures 8-11

). For metal stud partitions only, the single side mounting angle may be directly attached to the 

metal stud prior to the installation of the drywall.
  •  Retaining angles must be attached to the partition using one of the methods shown below:
    -  #10 screws of a length such that the screw engages the steel stud/track by ½ in. (13 mm) (steel framing).
    -  #10 screws of a length such that the screw engages the wood stud by 13/4 in. (44 mm) (wood framing).
    -  Steel anchors or self tapping concrete screws penetrating masonry or block 11/4 in. (31 mm).
  •  A minimum of two connections per side are required. Additional connections made at a maximum of 12 in. (305 

mm) O.C. for openings of 48 in. W x 36 in. H (1219 mm x 914 mm) and less. Dampers greater than 48 in. wide 
(1219 mm) or 36 in. high (914 mm) require the connections to be no more than 6 in. (152 mm) O.C.

Damper 
Sleeve

Angle Fastener

Stud or Runner

Two layers of 1/2 in. UL 
Classified Gypsum 
Wallboard for 2 hour 
rated walls. One layer 
for 1 hour rated walls 
(see UL Rated Wall 
Design for Additional 
Details). 

Figure 8: Single Side Angle With Steel Stud Wall 

Angle Over Wallboard

Stud or Runner

Damper

Sleeve

Angle Fastener

Two layers of 1/2 in. UL 
Classified Gypsum 
Wallboard for 2 hour 
rated walls. One layer 
for 1 hour rated walls 
(see UL Rated Wall 
Design for Additional 
Details).

Figure 9: Single Side Angle With Wood Stud Wall

Damper 
Sleeve

Metal Stud
or Runner

Two layers of 1/2 in. UL 
Classified Gypsum 
Wallboard for 2 hour 
rated walls. One layer 
for 1 hour rated walls 
(see UL Rated Wall 
Design for Additional 
Details).

Figure 10: Single Side Angle With Steel Stud Wall 

Angle Under Wallboard

Masonry or
Concrete
Wall

Damper

Sleeve

Angle Fastener

Masonry or
Concrete 
Floor

Damper

Sleeve

Angle Fastener

Top Side

Figure 11: Single Side Angle With Masonry or Concrete 

Wall and Floor

Grille Installations (Dampers up to 36 in. x 36 in. [914 mm x 914 mm])

Retaining angles used in conjunction with grille installations must be a minimum of 

5

8

 in. x 1 in. (15 mm x 25 mm) 16 

gauge (1.5 mm) steel. Space screws a maximum of 6 in. (152 mm) O.C. and a maximum of 2 in. (51 mm) from the 
corners (minimum of 2 screws per side). See 

Figure 12

 and 

Figure 13.

Note:

 Screws used to attach grille are allowed to penetrate reversed angle leg.

Curtain Fire Dampers

7

®

Содержание DFD 150 Series













Отзывы: