Green Frog Designs Chicken Run 2x2 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 17

background image

FITTING ELECTRIC FENCE SUPPORTS (Optional)

– same for all run sizes

Close up of a run with Electric Fence supports fitted (mesh/netting not shown for clarity)

28

Fit a Corner Bar Attachment at each corner of the
frame. If your door is hung from a corner vertical bar,
one of these will replace the standard Door Hinge
Holder. In this case, ensure that the hinge holes are
oriented towards the door. The door must open
inwards. Note: This stage is best done during frame
assembly.

29

Note: It is easiest to fit your mesh before the Wire
Holders are fitted.
Fit a Corner Wire Holder to each Corner Bar
Attachment using a Pi Clip. Then add a Corner Brace,
also using a Pi Clip. This drawing shows a corner that
does not have a door.

Printed on recycled paper

© Green Frog Designs Limited 2016

Page 16 of 17

«
...
14
15
16
17
»

Содержание Chicken Run 2x2


















Отзывы:

Нет отзывов

Похожие инструкции для Chicken Run 2x2

Бренд: NEC Страницы: 44

Бренд: XanLite Страницы: 4

Бренд: idi Страницы: 20

Бренд: G&G Страницы: 2

Бренд: H&S Страницы: 46

Бренд: Quick Страницы: 24

Бренд: JDS Uniphase Страницы: 144

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 14

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренд: Nautilus Страницы: 21

Бренд: Rainbow Страницы: 35

Бренд: Rain Harvesting Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Gardena Страницы: 33

Бренд: Backyard Adventures Playcenter Страницы: 33

Бренд: A.HABERKORN Страницы: 28

Бренд: Life Fitness Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды