background image

Air-to-water Heat Pump Split Versati

5

SPLIT

TYPE

  WARNING

Do not use means to accelerate the defrosting process or to clean, other than those 

recommended by the manufacturer. Should repair be necessary, contact your nearest 

authorized service centre. Any repairs carried out by unqualified personnel may be 

dangerous. The appliance shall be stored in a room without continuous operating ignition 

<$ =%#  

heater.) Do not pierce or burn.

Appliance shall be installed, operated and stored in a room with a floor area larger 

than Xm .(Please refer to table “a” in section of “ Safety Operation of Inflammable 

Refrigerant” for space X.)

Appliance filled with flammable gas R32. For repairs, strictly follow manufacturer’s 

instructions only. Be aware that refrigrants not contain odour. Read specialist’s manual.

 "  #"

for disconnection from the supply mains having a contact separation in all poles that 

provides full disconnection under overvoltage category III conditions, the instructions 

shall state that means for disconnection must be incorporated in the fixed wiring in 

accordance with the wiring rules.

This appliance can be used by children aged from 8 years and above and persons 

with reduced physical, sensory or mental capabilities or lack of experience and 

knowledge if they have been given supervision or instruction concerning use of the 

appliance in a safe way and understand the hazards involved. Children shall not play 

with the appliance. Cleaning and user maintenance shall not be made by children 

without supervision.

The appliance shall be stored in a well-ventilated area where the room size 

   " %

(for example an operating gas appliance) and ignition sources (for example an operating 

electric heater).

The appliance shall be stored so as to prevent mechanical damage from occurring.

  NOTE

   "% >?J

[ #"\ 

[   #  

[ #

Содержание VERSATI III Series
























































Отзывы: