background image

8

4. Clean or replace each filter.

6. Wash the air filters with water or clean them with vacuum

cleaner.

1. Vacuum dusts, and soak in warm water or water for about 10 to 15 minutes if dirt is heavy.

Remove the tabs on the filter frame and replace with a new filter.

2. Do not remove filter from frame when washing with water.

3. After washing, shake off remaining water and dry in the shade.

4. Since the material is made out of paper, do not wring out the filter when removing water from it.

See figure.

5. Set the air filter and Titanium Apatite Photocatalytic

Air-Purifying Filter as they were and close the front

panel.

• Operation without air filters may result in troubles as dust will accumulate

inside the indoor unit.

• If the dust does not come o

ff easily, wash them with neutral detergent

thinned with lukewarm water, then dry them up in the shade.

• Dispose of the old filter as flammable waste.
• Dispose of the old filter as flammable waste.

• It is recommended to clean the air filters every  week.

Air filter

Titanium Apatite 

Photocatalytic

Air-Purifying

Filter

The Titanium Apatite Photocatalytic Air-Purifying Filter can be renewed by washing it with water

once every 6 months. We recommend replacing it once every 3 years.

3.3

Titanium Apatite Photocatalytic

  Air-Purifying Filter

NOTE

Maintenance

Replacement

• O

peration with dirty filters:

(1) cannot deodorize the air.

(2) cannot clean the air.

(3) results in poor heating or cooling.   (4) may cause odour.

O

PERAT

IO

N

I

NSTRUCT

IO

NS

Maintenance

Содержание Multi21 CONS12HP230V1AF




























Отзывы: