18
Technical Information
Service Manual
10.SLEEP
Under COOL or HEAT mode, press this button, can select Sleep 1 (
), Sleep 2 ( ), Sleep 3 (
) and cancelthe Sleep, circulate
between these, after electrified,Sleep Cancel is defaulted.
Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run for one hour, the main unit setting temperature will increase 1
o
C , two
hours, setting temperature increa-sed 2 , then the unit will run at this setting temperature; In Heat mode: sleep status after run for one
hour, the setting temperature will decrease 1
o
C , two hours, setting temperature will decrease 2
o
C , then the unit will run at this setting
temperature.
Sleep 2 is sleep mode 2, that is air conditioner will run according to the presetting a group of sleep temperature curve.
Sleep 3-the sleep curve setting under Sleep mode by DIY;
(1)Under Sleep 3 mode, press "Turbo" button for a long time, remote controller enters into user individuation sleep setting status, at this
time, the time of remote controller will display "1hour", the setting temperature "88" will display the corresponding temperature of last
setting sleep curve and blink (The first entering will display according to the initial curve setting value of original factory);
(2)Adjust "▲" and " " button, could change the corresponding setting temperature, after adjusted, press "Turbo" button for confirmation;
(3)At this time, 1hour will be automatically increased at the timer postion on the remote control, (that are "2hours" or "3hours" or
"8hours"), the place of setting temperature "88" will display the corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours temperature setting finished, sleep,curve setting finished, at this time, the
remote controller will resume the original timer display; temperature display will resume to original setting temperature.
Sleep3- the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep curve, enter into user individuation sleep setting
status, but do not change the temperature, press "Turbo" button directly for confirmation. Note: In the above presetting or enquiry
procedure, if continuously within 10s, there is no button pressed, the sleep curve setting within 10s, there is no button pressed, the
sleep curve setting status will be automatically quit and resume to display the original displaying. In the presetting or enquiry procedure,
press "ON/OFF" button, "Mode" button, "Sleep" button, the sleep curve setting or enquiry status will quit similarly.
11.TEMP
Press this button, could select displaying the indoor setting temperature or indoor ambient temperature. When the indoor unit firstly power
on it will display the setting temperature, if the temperature’s displaying status is changed from other status to " ", displays the ambient
temperature, 3s later or within 3s, it receives other remote controller signal that will return to display the setting temperature.
12.I FEEL
Press this button to turn on I FEEL function. "
" icon is displayed on remote controller. The unit automatically adjust temperature
according to the sensed temperature. Press this button again to cancel I FEEL function. " " icon will disappear.
13.T-ON/T-OFF
T-ON button
"T-ON" button can set the time for timer on. After pressing this button, " " icon disappears and the word "ON" on remote controller blinks.
Press "▲" or " " button to adjust T-ON setting.
After each pressing "▲" or " " button, T-ON setting will increase or decrease 1min. Hold "▲" or " " button, 2s later, the time will change
quickly until reaching your required time. Press "T-ON" to confirm it. The word "ON" will stop blinking. " " icon resumes displaying.
Cancel T-ON: Under the condition that T-ON is started up, press "T-ON" button to cancel it.
T-OFF button
"T-OFF" button can set the time for timer off. After pressing this button," " icon disappears and the word "OFF" on remote controller
blinks. Press "▲" or " " button to adjust T-OFF setting.
After each pressing "▲" or " " button, T-OFF setting will increase or decrease 1min. Hold "▲" or " " button, 2s later, the time will change
quickly until reaching your required time. Press "T-OFF" word "OFF" will stop blinking. " " icon resumes displaying.
Cancel T-OFF. Under the condition that T-OFF is started up, press "T-OFF" button to cancel it.
Note:
Under on and off status, you can set T-OFF or T-ON simultaneously. Before setting T-ON or T-OFF, please adjust the clock time. After
starting up T-ON or T-OFF, set the constant circulating valid. After that, air conditioner will be turned on or turned off according to setting
time. ON/OFF button has no effect on setting. If you don’t need this function, please use remote controller to cancel it.
