Gree GRS-CQ12Pd/NaB-K Скачать руководство пользователя страница 46

Страница: 46 / 48

Air-to-water Heat Pump

The table of error code

Full Name

Displayed Name

Error Code

Ambient temperature sensor error

Ambient sensor

Condenser temperature sensor error

Cond. sensor

Discharge temperature sensor error

Disch. sensor

Suction temperature sensor error

Suction sensor

Outdoor fan error

Outdoor fan

Compressor internal overload protection

Comp. overload

High pressure protection

High pressure

Low pressure protection

Low pressure

High discharge protection

Hi-discharge

Incorrect capacity DIP switch setting

Capacity DIP

Communication error between indoor and outdoor unit

ODU-IDU Com.

High pressure sensor error

Pressure sens.

Heat exchanger-leaving water temperature sensor error

Temp-HELW

Auxiliary heater-leaving water temperature sensor error

Temp-AHLW

Refrigerant liquid line temperature sensor error

Temp-RLL

Heat exchanger-entering water temperature sensor error

Temp-HEEW

Water tank water temperature sensor 1 error

Tank sens. 1

Water tank water temperature sensor 2 error

Tank sens. 2

Refrigerant gas line temperature sensor error

Temp-RGL

Solar heater-leaving water temperature sensor error

Temp-SHLW

Room temperature sensor error

Sensor-RT

Water flow swich protection

WS-protection

Welding protection of the auxiliary heater 1

Auxi. heater 1

Welding protection of the auxiliary heater 2

Auxi. heater 2

Welding protection of the water tank heater

Auxi. -WTH

Under-voltage DC bus or voltage drop error

DC under-vol.

Over-voltage DC bus

DC over-vol.

AC current protection (input side)

AC curr. pro.

IPM defective

PFC defective

FPC defective

Start failure

Phase loss

Drive module resetting

Driver reset

Compressor over-current

Com. over-curr.

Overspeed

Sensing circuit error or current sensor error

Current sen.

desynchronizing

Desynchronize

Compressor stalling

Comp. stalling

Communication error

drive-main com.

Radiator or IPM or PFC module overtemperature

Overtemp.-mod.

Radiator or IPM or PFC module temperature sensor error

T-mod. sensor

Charging circuit error

Charge circuit

Incorrect AC voltage input

AC voltage

Drive board temperature sensor error

Temp-driver

AC contactor protection or input zero crossing error

AC contactor

Temperature drift protection

Temp. drift

Current sensor connection protection (current sensor not

connected to phase U/V)

Sensor con.

Communication error to the outdoor unit

ODU Com.

Communication error to the indoor unit

IDU Com.

Communication error to the drive

Driver Com.

Содержание GRS-CQ12Pd/NaB-K

















































Результаты поиска

Содержание GRS-CQ12Pd/NaB-K

Отзывы:

Похожие инструкции для GRS-CQ12Pd/NaB-K

Бренды по названию

Популярные бренды

Gree GRS-CQ12Pd/NaB-K, Руководство пользователя

Результаты поиска

Содержание GRS-CQ12Pd/NaB-K

Отзывы:

Похожие инструкции для GRS-CQ12Pd/NaB-K

Бренды по названию

Популярные бренды