Gree GRS-1.5/D150ANbA-K Скачать руководство пользователя страница 8

Страница: 8 / 81

GREE AIR SOURCE HEAT PUMP WATER HEATER SERVICE MANUAL

Model

GRS-1.5/TD150ANbA-K

GRS-1.5/TD200ANbA-K

Rated Heating Capacity

(*)

1500

Rated Input Power

(*)

429

COP

(*)

W/W

3.50

Capacity

150

190

Load Profile

COP

DHW

(**)

W/W

2.47

2.24

Energy Efficiency Class

(**)

Water Heating Energy Efficiency

(**)

104%

95%

Annual electricity consumption

(average climate conditions)

kWh

985

1075

Maximum Input Power

650+1500W (Electric Heater)

Outlet Water Temperature

°C

Default: 55°C, 35°C~70°C

Power Supply

220V-240V ~ 50Hz

Insulation Level

Ⅰ

Protection of Ingression

Ⅰ

PX4

Ⅰ

PX4

Refrigerant

Name

R134a

Charge

0.8

Outline Dimensions

W×D×H

621×561×1760

621×561×2030

Package Dimensions

W×D×H

731×717×1845

731×717×2110

Gross/Net Weight

112.0/92.0

122.5/102.5

Sound Power Level

(***)

dB(A)

Operating Range

°C

0~45

Notes:

①

(*) Value obtained with the following conditions: Outdoor temperature: 20°C DB/15°C WB; Water

tank temperature (start/end): 15°C /55°C.

②

(**) Value obtained with an air temperature of 7°C and a water inlet at 10

℃

, as per EN16147-2011,

(EU) No 814-2013.

③

(***) Value obtained indoor placement, as per EN 12102-2008, (EU) No 814-2013.

④

Under Rapid function, electric heater helps to heating water.

⑤

Please always see the nameplate for the exact data as this table is subject to change.

4.2 Work Temperature Range

Models

GRS-2.4/D270ANbA-K

GRS-1.5/D150ANbA-K
GRS-1.5/D200ANbA-K

GRS-1.5/TD150ANbA-K
GRS-1.5/TD200ANbA-K

Heating

-7~45°C

0~45°C

Note: The above value range indicates the outdoor ambient temperate range for normal operation of the
unit. For details on the configurable range of water temperature, see the nameplate of the water tank.

Содержание GRS-1.5/D150ANbA-K


















































































Результаты поиска

Содержание GRS-1.5/D150ANbA-K

Отзывы:

Похожие инструкции для GRS-1.5/D150ANbA-K

Бренды по названию

Популярные бренды

Gree GRS-1.5/D150ANbA-K, Руководство по обслуживанию

Результаты поиска

Содержание GRS-1.5/D150ANbA-K

Отзывы:

Похожие инструкции для GRS-1.5/D150ANbA-K

Бренды по названию

Популярные бренды