background image

GREE                                                      AIR SOURCE HEAT PUMP WATER HEATER SERVICE MANUAL

 

16 

 

4.5.2 Timer Setting 

Timer  setting: 

Under  the  HOTWATER  or  SAVE  mode  or  under  the  Off  state,  press  the 

TIMER 

button  to  enter  the  timer  setting  interface.  The  TIMER  and  ON  icons  are  on  and  the  hour  value  blinks. 
Press 

▲ or ▼

 to adjust the hour value and press the 

TIMER

 button to confirm setting. Then the minute 

value flickers. Press 

▲ or ▼

 to adjust the minute value and press the 

TIMER

 button to confirm setting. 

Then the OFF icon is on and ON icon is off. The hour value blinks. Press 

▲ or ▼

 to adjust the hour value 

and press the 

TIMER 

button to confirm setting. Then the minute value flickers. Press 

▲ or ▼ 

to adjust the 

minute  value  and  press  the 

TIMER

  button  to  confirm  setting.  After  the  scheduled  on/off  time  setting  is 

saved, the main interface is displayed. In the setting process, if no button is pressed within 15s, the main 
interface will be displayed and setting will not be saved. 

Timer cancelling:

 After the scheduled on/off time is set, press the 

TIMER

 button to cancel it. 

Note: 

The scheduled on time and off time cannot be the same; otherwise, the LCD switches to the 

interface for resetting the timer. 

 

 

4.5.3 Preset Time Setting 

In the PRESET mode, hot water is prepared in advance by the preset time. 

In the main interface of the PRESET mode, press the 

TIMER 

button to enter the selection interface. 

PRESET 1 blinks while PRESET 2 and PRESET 3 are not displayed. Press 

▲ or ▼

 and the LCD blinks 

Содержание GRS-1.5/D150ANbA-K


















































































Отзывы: