Gree GPC12AL-K3NNA1A Скачать руководство пользователя

Страница: 30 / 69

Maintenance

Service Manual

NO.

Malfunction
Name

Display Method of Indoor Unit

A/C Status

Possible Causes

Error

Code

Indicator lamp

(During blinking, ON for 0.5S and

OFF for 0.5 S)

Operation

Inidicato

COOL

Indicator

HEAT

Indicator

Water

over-flow

protection

The unit stops

operation

During cooling or drying

operation,condensate water will flow into

chassis. If its detected that water inside

water chassis is full for 3s successively,

it comes into water over-flow protection.

Buzzer will give out 8 sounds and dual-8

nixie tube displays error code “H8”.

Insufficient

fluorine

protection

Indoor fan runs

according to set fan

and other loads will

stop.

1. Heat exchangers are too dirty or the air

inlet/outlet is blocked.

2. Compressor doesnt work normally. Strange

noise or leakage occurs. Temperature of the

shell is too high.

3. System is blocked inside(dirt block, ice

block, oil block, Y-valve not fully open).

4. The refrigerant is leaking.

Overload

protection for

compressor

Indoor fan runs

according to set fan

and other loads will

stop.

1. Heat exchangers are too dirty or the air

inlet/outlet is blocked.

2. Fan motor is not working Abnormal fan

speed; fan speed is too low or the fan doesnt

run.

3. Compressor doesnt work normally. Strange

noise or leakage occurs. Temperature of the

shell is too high.

4. System is blocked inside(dirt block, ice

block, oil block, Y-valve not fully open).

5. Draw-water motor cant operate normally.

6. Water outlet hasnt been blocked well by

rubber cork .

7. The refrigerant is leaking and cause

overheating protection to compressor.

8 Overload

malfunction

During cooling or

drying operation,

indoor fan operates,

while compressor,

outdoor fan and

water-striking

motor stop. “E8” is

displayed.

1. The environment is formidable.

2. Heat exchangers are too dirty or the air

inlet/outlet is blocked.

3. Fan motor is not working Abnormal fan

speed; fan speed is too low or the fan doesnt

run.

4. Compressor doesnt work normally. Strange

noise or leakage occurs. Temperature of the

shell is too high.

5. System is blocked inside(dirt block, ice

block, oil block, Y-valve not fully open).

6.Temperature sensor of main board cant

detect correctly.

Содержание GPC12AL-K3NNA1A






































































Результаты поиска

Содержание GPC12AL-K3NNA1A

Отзывы:

Похожие инструкции для GPC12AL-K3NNA1A

Бренды по названию

Популярные бренды

Gree GPC12AL-K3NNA1A, Руководство по обслуживанию

Результаты поиска

Содержание GPC12AL-K3NNA1A

Отзывы:

Похожие инструкции для GPC12AL-K3NNA1A

Бренды по названию

Популярные бренды