Gree CB11500430, Руководство по обслуживанию

Страница: 18 / 67

Setting the Room Temperature Set Point
Pressing the “TEMP +” and “TEMP --” buttons will raise or lower
the temperature.
The unit will confirm signal receipt with a beep and the value of
the set temperature on the display, on the remote control, and on
the front panel, will change accordingly.
The temperature can be set between 61
_
F (16
_
C) and 86
_
F
(30
_
C).
NOTE: In Cooling mode, if the temperate selected is higher than
the room temperature, the unit will not start. The same applies for
the Heating mode if the selected temperature is lower than the
room temperature.
Selecting the Fan Speed
LOW
MEDIUM
HIGH
AUTO
A08304
The fan speed can be selected by pressing the “FAN” button.
NOTE: When the unit is on, the fan will run continuously in
cooling or heating. When in heating, there might be situations
where the fan will slow down or shut off to prevent cold blow.
Selecting the Horizontal Direction Louver Position
When the unit is turned on, the louvers default to the cooling or
heating position.
If the louver position is not providing adequate comfort due to
room layout or where people are gathered, the user has two
options:
1. Have the horizontal louvers move continuously. This is ac-
complished by pushing the “SWING” button. When this
button is pushed, the “SWING” icon will appear on the re-
mote control and the louvers will operate in a preset range
as shown in the figure below.
COOLING
HEATING
A08307
2. If a stationary position other than the default position is pre-
ferred, push the “SWING” button once and allow the louver
to move to the desired position then push the “SWING”
button again.
NOTE: Always use the remote control to adjust the louver
position otherwise, abnormal operation may occur. If the
louver is manually adjusted out if its range, turn the unit off
and then on again.
Sometimes, in the heating mode, when the “SWING” button is
pushed, the louvers will not start moving right away. This is
due to the fact that the fan will not start running until the coil
temperature is warm enough to prevent discomfort to the user
by blowing cold air.
Selecting Vertical Direction of the Louver
The vertical louvers can be adjusted manually to direct the airflow
to achieve the optimal comfort in the space.
A07543
Timer Function
TIMER ON (to start the unit) and TIMER OFF (to stop the unit)
can be used separately or together. The clock on the remote control
must be set before using this function.
Timer ON only
Timer ON Indicator
A08305
This function will allow the unit to start automatically at the set
time. The TIMER ON can be set while the unit is on or off.
To set the TIMER ON function, perform the following:
1. Push the “T--ON” button once.
2. The timer indicator will appear on the remote control with
“ON” flashing.
3. Push the “TIME --” or “TIME +” until the desired on time
is reached.
NOTE: Pressing the “TIME --” or “TIME +” will decrease or
increase the time in 1 minute increments.
Pressing the “TIME --” or “TIME +” continuously will
decrease or increase the time in 10 minute increments.
4. Push the “T--ON” again. The “ON” icon will stop blinking
and the time at which the unit will start is set.
The “T--ON” time will be stored in memory indefinitely until it is
cancelled by the user by pushing the “CANCEL” button or the
remote control batteries are replaced.
If the unit is running and the “T--ON” set time is reached, the unit
will continue operating normally.
NOTE: When the unit is shut off by the user using the
“ON/OFF” button, and if the “T--ON” is set, the following will
be displayed on the remote control.
-- Set Point
-- Time
-- “TIME ON” icon
On the display panel, the operation light will turn red.
When the “T--ON” is reached, the display on the remote does
not change, and the unit is running as indicated by the
operation light on the front cover turning green. To get display
on the remote, push the “ON/OFF” button once.
15