GREAT PLAINS YP4425A Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 170

GREAT PLAINS YP4425A Скачать руководство пользователя страница 36

2018-07-30

Table of Contents

401-805M

YP4425A

Table of Contents

Operating Instructions

32

Transporting the

Planter

Loss of Control Hazard:

Ensure that the towing vehicle is adequate for the task. Using
an inadequate tow vehicle is extremely unsafe, and can result
in loss of control, serious injury and death.

The planter can weigh over 28000 pounds (12 500 kg),
depending on configuration and seed load. A tank cart hitched
to the planter (“in train”) adds another 5000 pounds
(2268 kg) empty. The tractor unit MUST be rated for the load.
If the tractor is not rated for at least 28000 pounds, calculate
or obtain a scale weight of the planter and cart.

Do not tow if planter exceeds the load rating of the vehicle.

Loss of Control Hazard:

A tank cart in train must be EMPTY. A full tank cart weighs
nearly 30000 pounds (13608kg), and, when hitched to the
planter, represents an unsafe highway load regardless of the
rating of the towing vehicle. If a cart must be transported
loaded, tow it separately.

Check Bridge Loads

: A loaded planter, or a planter with cart

in tow, can exceed the load ratings of bridges you must cross.

Loss of Control Hazard:

The CFM switch must be set to Hitch, and the hydraulic circuit
must be in FLOAT during transport. Failure to do this may
result in hydraulic system damage, transport hooks unlatching,
and major planter/tractor damage.

Braking and Loss of Control Hazard:

Do not exceed 20 mph (32 km/h) when driving straight.

The planter is extremely heavy, and can cause “over-steer”
with most tractors. Do not exceed 13 mph (22 km/h) in turns.

Do not exceed 3 mph (5 km/h) in reverse.

Reduction of Control Risk:

Seed may be loaded prior to travel, but increases stopping
distance, increases the need for caution in turns and braking,
and increases tire wear.

Never back up with the planter lowered or with a fertilizer tank
hitched to the planter.

Never back the planter if PFC cart is attached.

.eps

100%

29284

29284

22

32

5

«
...
34
35
36
37
38
...
»

Содержание YP4425A











































































































































































Отзывы:

Нет отзывов