GREAT PLAINS YP2425 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 166

background image

YP2425 and YP2425F

Table of Contents

Options

121

2016-11-16

Table of Contents

401-406M

Coulter Blades

Replacement and alternate coulter blades include the
following. Order one blade per row unit.

For operations, see:
“

Coulter Adjustments

” on page 71.

Gauge Wheel Scrapers

When planting in moist or sticky soils, these scrapers are
useful in preventing build-up that might otherwise result
in shallow planting.

Order one part per wheel (2 per opener).

The scrapers mount on the bottom rear of the depth
wheel arm, using the existing bolt and lock washer. The
slot in the scraper is long enough to clear the lower
grease zerk, and allow adjustment as wheel and scraper
wear.

For operations, see:
“

Adjusting Gauge Wheel Scrapers

” on page 75.

Seed Meters

Seed meters are not standard in the base YP24
configuration. Normally, one or more sets are ordered
with the original planter. One set is factory-installed.

Meters are simple to change. Available models include
(part numbers are for a single row unit; each Singulator
Plus includes one seed wheel).

For operations, see:
“

Seed Meter Setup and Adjustment

” on page 76.

15 inch Turbo Packages

Part Number

Fluted, 15 inch (20 flutes)

820-327C

Turbo, 15 inch (50 flutes)

820-331C

Straight, 14 inch

820-259C

25299

Wheel Scrapers

Part Number

2

1

/

2

in. (6.4cm) Gauge wheel scraper

404-194D

3 in. (7.6cm) Gauge wheel scraper

404-195D

4 in. (10.2cm) Gauge wheel scraper

404-196D

Meters

Part Number

Singulator Plus

403-156K

12FP 12-Finger Pick-Up (30 inch)

403-158K

12FP 12-Finger Pick-Up (sunflower)

403-203K

6FP 6-Finger Pick-Up (Twin/20 inch)

403-169K

25298

25294

«
...
123
124
125
126
127
...
»

Содержание YP2425







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP2425

Бренд: AL-KO Страницы: 116

Бренд: Gardenline Страницы: 30

Бренд: Gravely Страницы: 25

Бренд: MTD Страницы: 16

Бренд: Texas Страницы: 16

Бренд: MTD Страницы: 16

Бренд: SaMASZ Страницы: 52

Бренд: Ryobi Страницы: 36

Бренд: Yazoo/Kees Страницы: 72

Бренд: Yard Machines Страницы: 28

Бренд: Snapper Страницы: 20

Бренд: GreenWorks Страницы: 31

Stockman 4000 A16314E

Бренд: COX Страницы: 50

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды