GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 39

Страница: 39 / 190

YP4025A-48TR20

Table of Contents

Index

Operating Instructions

2019-03-19

Table of Contents

Index

411-198M

wheels, and tank cart lead wheel fully caster, and provide no

resistance to side sway by the implement name or cart.

Reduction of Control Risk:

Seed may be loaded prior to travel, but increases stopping

distance, increases the need for caution in turns and braking,

and increases tire wear.

Never exceed 3 mph (5 km/h) in reverse.

Never back up with the implement name lowered or with a
pull-type fertilizer tank hitched to the implement name.

If towing other than with a suitable tractor, and the weight

transfer option is present, install shipping links (page 166).

Typical Implement Name Weights



The figures in the table at right represent a limited

number of configurations. The weight of your product

can vary by thousands of pounds, even if it is the

same base model, due to installed options and/or

aftermarket equipment.

If your tractor weight or capability is near its limits,

take your empty product to a scale and get a precise

weight.

Steering

Never exceed 13 mph (22 km/h) in turns. The implement

name is extremely heavy, and can cause “over-steer”

with most tractors. The leading gauge wheels, rear-most

transport wheels, and tank cart lead wheel fully caster,

and provide no resistance to side sway by the product or

cart.

Base Model, Empty

34,000 lbs

15 400 kg

Base Model + Material Load

43,000 lbs

19 500 kg

Add for SML-735, Empty

3000 lbs

1300 kg

Planter with Cart

Planter and Cart Empty

36,900 lbs

16 800 kg

Planter and Cart, Full*

54,800 lbs

24 800 kg

Configuration: Markers, Unit-
Mounted Coulters and Hopper

YP4025A-48TR20

150bu Hopper

* Figures included only to emphasize the hazard.

Never

tow a loaded tank cart hitched to a planter.

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды