GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 36

Страница: 36 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Operating Instructions

2019-03-14

Table of Contents Index

195-067M

Unfolding

Drill must be lowered from transport lift prior to unfolding.

See “

Lowering Drill (Transport Lift)

” on page 31.

1. Verify that the site has clearance needed to unfold

drill.

2. If markers are installed, set Marker/Fold selector

valve to Fold (page 43).

Refer to Figure 18

3. Verify that the opener sub-frames are still raised and

locked up (handles in ROAD position).

4. Slowly supply oil to base end of fold circuit. Unfold

wing frames by completely extending fold cylinders.

If field operations are planned:
5. Position all six opener transport lock handles in

FIELD position.

6. Completely raise openers to allow opener transport

locks to disengage.

Note: The opener transport lock handles are spring

loaded and can be moved to field position with

openers up or down, but locks will only disengage

when openers are completely raised. There are

two lock handles on each drill section.

Folding and Unfolding Quick Reference

To Fold Drill for Transport

• Fold markers (page 43).
• Raise openers (page 26).
• Fold drill (page 27).
• Raise drill (page 28).

To Unfold Drill for Field

• Lower drill (page 33).
• Unfold drill (page 33).
• Set openers for FIELD (page 26).

Figure 27 - Unfold

Opener Unlock

15549

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 36 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: