GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя страница 110

Страница: 110 / 118

2018-06-18

Table of Contents

Index

195-441M

3S-3000/F/HD/HDF

Table of Contents

Index

Appendix B - Initial Setup

106

Appendix B - Initial Setup

Scraper Installation

Optional disk scrapers are not factory installed. To install
them in the field:

Remove one or both disk blades to gain safe access
to the mount. Note the position of bushings and
spacers for correct re-assembly (page 56).

Refer to Figure 95

Position the inside scraper mount

to the rear of

the seed firmer mount

on the opener weldment.

Secure it with two HHCS



-16x1in hex head bolts,

lock washers and nuts. Insert the bolts from the front.

Position the scraper blade

below and behind the

inside scraper mount

, with the notch on top to

machine right.

Secure it loosely with one RHSNB



-16x1 round

head square neck bolt, flat washer, lock washer and
nut.

Re-mount the removed disk blade.

Adjust the scraper blade per “

Disk Scraper

Adjustments

” on page 56.

Figure 95

Scraper Installation

26460

Содержание 3S-3000-3210























































































































Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000-3210, Руководство оператора

Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды