GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Adjustments

56

Disk Blade Adjustments

Opener disc angle and stagger is not adjustable, but
disc-to-disc spacing is, and may need attention as discs
experience normal wear. Spacers will need to be reset
when blades are replaced.

Refer to Figure 56

The ideal spacing causes the blades to be in contact for
about one inch. If you insert two pieces of paper between
the blades, the gap between them should be 0 to 1.75in
(0-4.4cm).

If the contact region is significantly larger or smaller (or
there is no contact at all), it needs to be adjusted by
moving one or more spacer washers. If the contact
region varies with blade rotation, one or both blades is
likely bent and in need of replacement.

Adjusting Disc Contact

Sharp Object Hazard:

Row unit disk blades may be sharp. Use

caution when making adjustments in this area.

Refer to Figure 57

1.

Raise the drill and lock it up by moving the
Transport/Field handle to TRANS.

2.

Remove the bolt

retaining the opener disc on one

side. Carefully remove the blade

, noting how

many spacers

are outside the flange dust cover

and inside the disk. Do not lose the hub components
and spacers.

3.

To reduce the spacing between the discs (the normal
case), move one spacer washer from the inside to
the outside of the flange dust cover.

4.

Re-assemble and check disc contact.

Disk Scraper Adjustments

Sharp Object Hazard:

Row unit disk blades may be sharp. Use

caution when making adjustments in this area.

Disk scrapers are optional. See page 94 ordering
information and page 106 for installation. To keep opener
disks turning freely, dirt scrapers are mounted between
disks to clean as disks rotate.

Refer to Figure 58

As field conditions vary, scrapers may need to be
adjusted. In damp conditions, lower scrapers. If openers
are not turning freely, raise scrapers. To adjust, loosen
bolt and move scraper as needed.

Figure 56

Checking Disk Contact

26395

Figure 57

Adjusting Disk Spacers

26385

4

1

3

2

Figure 58

Opener Disk Scraper

26463

«
...
58
59
60
61
62
...
»

Содержание 3S-3000-3210























































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-3000-3210

Бренд: GE Страницы: 209

Бренд: ESD Страницы: 6

Бренд: Abicor Binzel Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды