manualshive.com logo in svg

GREAT PLAINS 1006NT, Оригинальное руководство пользователя

Поделиться
Скачать
GREAT PLAINS 1006NT Скачать руководство пользователя страница 17

706/1006NT

Table of Contents

Assembly

13

01/22/2018

Table of Contents

150-285Q

Route Hoses and Harness

The hydraulic hoses are pre-installed on the drill and are
tied to the hitch mounting plate.

Refer to Figure 9

1.

Connect the rear lighting harness (1) to the red and
amber lamps.

2.

Fasten the module (2) of the middle lighting harness
(3) to the tongue with 1/4-20x1 inch bolts (4) and
nuts (5). Connect the middle lighting harness to the
rear wiring harness.

3.

Connect the front lighting harness (6) to the middle
lighting harness. Use wire ties (7) to fasten the wiring
harnesses to the drill.

4.

Tape or tie the tractor connector (8) on the front
lighting harness to the hose bundle at the
quick-disconnect fittings.

Refer to Figure 10

5.

Route the hose and harness bundle (9) under the
rear cross-tube of the tongue, into the access hole
(10), and out the front of the tongue tube near the
hitch.

6.

Un-tape/tie the lighting harness. Fasten the lighting
connector and hydraulic quick disconnect fittings to
the holder plate (11).

Deferred Option Assembly

Some optional drill features are not factory-installed, or
may have been ordered for field installation. Although
they are “assembly” items, they may require a hitched
tractor, and/or that drill hydraulics are already functioning
(for drill lift/lower); steps not yet completed.

If any of the following items require installation, defer
them until page 21 of “

Setup

”:

•

Native Grass

•

Agitator

•

Fertilizer

•

Seed Firmers

•

Small Seeds

•

Harrow

3

1

68366A

2

6

7

8

4

5

Figure 9

Connect Light Harnesses

Figure 10

Route Hoses and Harness

21718

9

11

10

Содержание 1006NT



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды