manualshive.com logo in svg

Gravely 992111, Руководство владельца и оператора

Поделиться
Скачать
Gravely 992111 Скачать руководство пользователя страница 22

GB - 26

NOTE: The PTO idler spring length range is 13 to 13.25 in. 
(33 to 33.6 cm) measured at a 3 in. (7.6 cm) cutting height. 
Adjust the idler spring length as needed, see figure 21.

5. Install belt guard on rear of unit.

6. Install left hand belt cover on mower deck.

7. Close footboard (see MOWER DRIVE BELT AND PTO 

BELT ACCESS on page 25).

MOWER DRIVE BELT REMOVAL

Removal (Figure 20)

NOTE: The PTO belt must be removed from blade spindle 
pulleys prior to removing mower drive belt. The PTO belt 
does not need to be removed from electric clutch.

1. Remove PTO belt from blade spindle pulleys (see PTO 

BELT REMOVAL on page 25).

2. Remove mower drive belt from right blade spindle pulley 

and then from center blade spindle pulley.

3. Loosen drive belt idler pivot bolt just enough to gain 

clearance to remove mower drive belt from under drive 
belt idler.

4. Remove mower drive belt from unit.

Installation (Figure 20)

1. Install the new mower drive belt on center blade spindle 

pulley, right blade spindle pulley, and drive belt idler.

2. Tighten drive belt idler pivot bolt.

3. Install PTO belt on blade spindle pulleys (see PTO BELT 

REMOVAL on page 25).

TRANSMISSION BELT REMOVAL (992111, 113, 
115, 117,  124, 127, 128, 129, 130, 131, 132, 133, 
134, 135, 139, 145)

Removal (Figure 22)

1. Remove PTO belt from electric clutch (see PTO BELT 

REMOVAL on page 25).

2. Remove clutch anchor.

3. Slowly release the tension on the hydro pump belt idler 

until all the tension is removed from the springs. 

4. Remove old hydro pump belt from right hand hydrostat 

sheave first.

Installation (Figure 22)

1. Install new hydro pump belt by positioning belt on 

sheaves. Put belt onto right hand hydrostat sheave last.

2. Replace clutch anchor.

3. Install PTO belt on electric clutch (see PTO BELT 

REMOVAL on page 25).

TRANSMISSION BELT REMOVAL (992121, 123, 
125, 126, 136, 137, 138)

Removal (Figure 23)

NOTE: A 1/2-inch ratchet driver is needed to remove 
transmission belt.

1. Place unit in the service position (see SERVICE 

POSITION on page 20).

.

OF3229

Figure 21

The PTO idler spring length range is 13 to 13.25 in. 
(33 to 33.6 cm) measured at a 3 in. (7.6 cm) cutting 
height. Adjust as necessary.

Measure PTO idler 
spring length here.

PTO Idler Spring Length

CAUTION: Use care when releasing idler spring 
tension. Keep body parts well away from idlers 
when performing this operation.

CAUTION: Use care when releasing idler spring 
tension. Keep body parts well away from idler when 
performing this operation.

OF1631

1. Right Hand Hydrostat
2. Hydro Belt
3. Left Hand Hydrostat
4. Spring

5. Clutch
6. Clutch Anchor
7. Engine Sheave
8. Idler

Figure 22

1

2

3

4

5

6

7

8

Содержание 992111





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды