GRAUPNER HoTT MC-16 Series, Руководство по программированию

Страница: 96 / 332

96 Program description - Base setup models | Helicopter models
1
bind
BD1
ET
BD2
Rcv R08
Mod.
Stick
modu
Base setup model
RF
must be
OFF
OK
Press the central SET button of the right-hand four-
way button to erase the message.
Drop down two lines in the screen and switch off the
RF module as described on the page in section “RF
module”. Afterward, return again to the “Module” line
and restart the binding process as described above.
Alternatively, the transmitter can be switched off
briefly then, after switching it back on again, respond
to the message window that appears …
P l e a s e s e l e c t
R F o n / o f f ?
O N O F F
… with “OFF” …
P l e a s e s e l e c t
R F o n / o f f ?
O N O F F
… then confirm the selection with a brief tap on the
center
SET key of the right four-way button. From the
base screen jump again into the “Module” line of the
»Basic settings, model« menu and restart the bind-
ing process.
Dissolving a bond
Proceed as described above to initiate the binding
process but WITHOUT first putting a receiver in bind-
ing readiness.
EXT. (PPM signal at DSC socket)
If your transmitter is fitted with a non-Graupner|SJ
external RF module connected to the DSC / Data
socket, you can switch between the standard internal
HoTT RF module and the external module when you
switch model memories in the “Module” line by choos-
ing either “HoTT”, “EXT.”, or “SP.”, as described in the
following section.
You can now use the arrow button

of the right-hand
four-way button to move to the first Value field in the
“Module” line before pressing the central
SET button
of the right-hand four-way button:
1
bind bind
BD1
STARLET
BD2
Rcv Ch Map R12 R08
Mod.name
Stick mode
module
Base setup model
HoTT
In the active Value field you should now use the Se-
lect buttons to choose “EXT.” or – if appropriate – the
“SP.” mode (described below) instead of “HoTT”.
When you select “EXT.”, the HoTT-specific value fields
are replaced by the modulation type already selected
in the “DSC output” line; see page 100:
1
PPM10
STARLET
EXT.PPM sig. normal
Mod.name
Stick mode
module
Base setup model
EXT.
The lines of the “Receiver output” and “Range test”
options (described below) are also suppressed, as
are all the HoTT-specific displays in the base display;
“PPM” is also superimposed instead of “HoTT”:
STARLET
#02
0:12h
Stp
Flt
0:00
0:00
4.0V PPM
Press the central SET button of the right-hand four-
way button to conclude the Select process.
SP. (digital signal at Data socket)
However, if you require a special digital signal instead
of the analogue PPM signal for the non-Graupner|SJ
external RF module, then connect this to the DATA
socket and select “SP.” in the “Module” line:
1
BD
STARLET
SP channel 6
SP. BIND 1
Mod
Mod.name
Stick mode
module
Base setup model
Once again, press the central SET button of the right-
hand four-way button to conclude the Select process.
The lines of the “Receiver output” and “Range test”
options (described below) are also suppressed, as
are all the HoTT-specific displays in the base display;
“SP.” is also superimposed instead of “HoTT”:
STARLET
#02
0:12h
Stp
Flt
0:00
0:00
4.1V SP