23 February 2004
Set up RAID Storage: PFC 500/E (Local storage only)
9
Connect Fibre Channel cabling.
Set the Fibre Channel Loop Address ID on each RAID Controller as shown.
2
1
Power Cord
(115V/230V)
Power Cord
(115V/230V)
Optional
Power Supply
Connect power cords and turn on power as shown.
Begin with PFC
500E(s), if installed. Verify proper power-up as shown.
0
1
2
3
4
5
6
7
8
9
#
0
2
4
1
3
5
#
6
8
1 0
7
9
1 1
0
1
2
3
4
5
6
7
8
9
#
0
2
4
1
3
5
#
#
6
8
1 0
7
9
1 1
#
0
2
3
Set Chassis
Addresses
1
Lower the
front door
Set required chassis addresses, refer to Step .
A
P/S
B
ON
l
OFF
0
ON
l
OFF
0
3
4
PFC 500 Chassis Address = 0
PFC 500E* Chassis Address = 1
PFC 500E* Chassis Address = 2
* If Installed
PFC 500* Chassis Address = 0
PFC 500E* Chassis Address = 1
PFC 500E* Chassis Address = 2
Pull out
controller
PFC 500 Rear Panel
A
B
Lift handle
Optional Redundant
RAID Controller
Primary
RAID Controller
RAID Controller Board
C
0
7
6
5
4
3
2
1
0
E
C
A
8
6
4
2
F
D
B
9
7
5
3
1
0
7
6
5
4
3
2
1
0
E
C
A
8
6
4
2
F
D
B
9
7
5
3
1
Top Switch
(always set to "0")
Set Fibre Channel
Loop Address ID
settings. Refer to
the table.
Maximum of 5 PFC
500 Chassis
0626-13
Media Platform
Port A
Port B
0
1
2
3
4
5
6
7
8
9
#
0
2
4
1
3
5
#
6
8
1 0
7
9
1 1
System Check LED
Power LED
Power-up Verification
Power LED is on.
System Check LED turns off after approximately 90
seconds.
The PFC500 requires approximately 2 to 3 minutes
to fully initialize. All disk access LEDs are on.
Refer to the
PFC
500 Instruction Manual if there is
a problem.
2
Number of
PFC
500s *
* For systems with greater than three PFC500s, use the
same numbering pattern as shown.
PFC 500
Chassis
Primary
Controller
Address ID
Redundant
Controller
Address ID
1
2
3
First
First
Second
First
Second
Third
0
0
1
0
1
2
1
2
3
3
4
5
Fibre Channel Loop Addresses
Redundant system cabling
Copper SFPs
IMPORTANT: If you are installing your PVS2000 as part of an Open SAN, do not perform this RAID
3
Set up RAID Storage: PFC500/E
(Local storage only)
Use this diagram to set up the PFC 500 Fibre Channel RAID Chassis and the PFC 500E
Expansion Chassis (if used).
Содержание Profile XP PVS1000
