GRASS VALLEY Profile XP PVS1000 Скачать руководство пользователя страница 13

Страница: 13 / 46

23 February 2004

Set up RAID Storage: PFR600/E (Local storage only)

IMPORTANT: If you are installing your PVS2000 as part of an Open SAN, do not perform
this RAID storage setup. Instead, follow the instructions in the

Open SAN Instruction

Manual

for setting up RAID storage.

Power Cord
(115V/230V)

Install ethernet cabling and switch or hub as shown.

Install serial cabling as shown.

PFR 600

RAID

Chassis

PFR 600E*

Expansion

Chassis

PFR 600E*

Expansion

Chassis

Media Platform

Ethernet Hub or Switch

Power-up Verification

Rear panel "7 Segment LED" displays the chassis address as
set in step .

All disk drive LEDs are green after approximately 3 minutes.

Refer to the PFR 600 Instruction Manual if there is a problem.

Disk Drive LEDs

7 Segment

LEDs

PFR 600

RAID

Chassis

PFR 600E*

Expansion

Chassis

PFR 600E*

Expansion

Chassis

Caution: See serial cabling detail below.

Media Platform

After RAID Controller A is configured,

the standard serial cable will be moved

to this connector to configure RAID

Controller B, if installed.

Maximum of 4 Expansion Chassis

* If Installed

This cable used for PFR 600s
with optional RAID Controller B.

This cable used for
PFR 600 chassis with optional
RAID Controller B.

Standard
Serial Cable

Serial Cabling Detail

(Applies to primary and

redundant cabling)

Always plug the end

connector of dasiy

chain cable into last

expansion chassis.

Always plug the first connector

into the PFR 600 RAID Controller.

Leave
unconnected

Connect power cords, and turn on power as shown.
You must power-up the PFR

600E Expansion

chassis prior to, or at the same time as the PFR

600

RAID Controller chassis. Verify power-up as shown.

Set up RAID Storage: PFR600/E
(Local storage only)

Use this diagram to connect Ethernet and serial interface cabling required for monitoring the
PFR 600/E with NetCentral Lite or NetCentral Manager.

Содержание Profile XP PVS1000















































Результаты поиска

Содержание Profile XP PVS1000

Отзывы:

Бренды по названию

Популярные бренды

GRASS VALLEY Profile XP PVS1000, Руководство по установке

Результаты поиска

Содержание Profile XP PVS1000

Отзывы:

Бренды по названию

Популярные бренды