GRASS VALLEY 8910ADA-M - Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 58

background image

8910ADA-M/ST/SR — Instruction Manual

15

Installation

Front Module Installation

After installing the rear module, install the front module as follows:

1.

If using local onboard controls, set jumpers on the module circuit board
as required. Refer to

Onboard 8910ADA-M and -ST Configuration

Onboard 8910ADA-SR Configuration

before

installing the front module.

2.

Remove the front cover of the frame.

3.

Locate the corresponding front slot.

4.

Insert the front module so that the plastic card guides on the module
top and bottom edges go over the upper and lower raised rail guides on
the right of the top and bottom of the slot(

).

5.

Carefully slide the module into the rear connector.

6.

Lock the front module ejector tab into the locking pin.

7.

Reinstall the front cover of the frame during normal operation.

Figure 4. Front Module Installation

Slide top and bottom card carriers on module
over top and bottom guides on right of slot.

Module installed

Locking Pin

Front Module Side View

0642_10r0

«
...
13
14
15
16
17
...
»

Содержание 8910ADA-M -



























































Отзывы:

Нет отзывов

Похожие инструкции для 8910ADA-M -

Бренд: NAD Страницы: 16

Бренд: NAD Страницы: 2

Бренд: Ecler Страницы: 20

Бренд: Ecleree Страницы: 28

Бренд: Ecleree Страницы: 42

Бренд: X4-TECH Страницы: 16

Бренд: XINDAK Страницы: 10

Бренд: Pyle Pro Страницы: 2

Бренд: Pyle Страницы: 8

Бренд: PowerBass Страницы: 24

Бренд: Sherwood Страницы: 14

openGear DEA-8205

Бренд: Ross Страницы: 32

Бренд: Denon Страницы: 12

Бренд: Stagg Страницы: 2

Бренд: ELECTROCOMPANIET Страницы: 8

Бренд: Summit Audio Страницы: 20

Бренд: Harman Kardon Страницы: 8

Бренд: E&I Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды