GRASS VALLEY 7500NB Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 92

background image

7500 Series Instruction Manual

Glossary-3

Crosspoint (XPT)

An electronic switch that allows a signal to
pass from an input to an output when the
switch is closed.

DA

Distribution Amplifier. The Series 7000 uses
DAs to expand outputs.

Data Matrix

A signal processing matrix containing mod-
ules that route RS-422 or RS-485 data.

Default

The setup condition existing when a device
is first powered-up or after a system restart.

Destination (DEST or DST)

The point to which Source signals are rout-
ed. In Series 7000, a Destination may include
one or more outputs, across multiple Levels,
with any connector number offset (user-de-
fined in system configuration). (See Multi-
level Switching in Section 1.)

Destination Exclusion Set (DXS)

User-determined set of Destinations exclud-
ed from control by a particular panel. If used,
Destination Exclusion Sets are included in a
Panel Template before the template is down-
loaded to a particular control panel. A specif-
ic Destination Exclusion Set may be shared
by more than one panel template.

DGND

Digital Ground.

DST

See

Destination (DEST or DST)

DSVOM

Dual Sync Video Output Monitor. Part of the
DV Series.

Dumb Terminal

A conversational slave to a host computer.

EC I/F

External Control Interface.

EDP

Eight Destination Paging control panel.

EMI

Electromagnetic interference.

ENC

Enhanced Node Controller. Designed to re-
place the Node Controller it can be used in all
Classic and DV Series matrices. The ENC is
required for Dual Control of a matrix by the
Series 7000 Control System and an external
device such as a PC. The ENC does not sup-
port the Kscope Interface Mezzanine.

EPROM

Erasable Programmable Read Only Memory.
EPROMs are non-volatile memory chips.
They are commonly called Flash memory
chips.

ERR

Error. This is commonly found on the mod-
ules to identify the red error LED.

Ethernet

A local area network (LAN) technology ca-
pable of transmitting information between
computers at speeds of 10 and 100 Mbps.

Exclusion

User-determined Sources excluded from
routing to a particular Destination.

FC

Frame Controller.

FET

Field Effect Transistor.

First Come First Served (FCFS)

Tieline status where it is not necessary to cre-
ate a reservation to use the specified Tieline.

«
...
75
76
77
78
79
...
»

Содержание 7500NB





























































































Отзывы:

Нет отзывов

Похожие инструкции для 7500NB

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: Observint Страницы: 117

xCORE-200 Multi-channel Audio board

Бренд: XMOS Страницы: 112

3C410012A - OfficeConnect Remote 531 Access...

Бренд: 3Com Страницы: 72

Бренд: Qlogic Страницы: 2

Бренд: Magnadyne Страницы: 8

Speed Touch 591s

Бренд: Alcatel Страницы: 184

HiGain H2TU-R-402 List 7A

Бренд: ADC Страницы: 7

Бренд: Renesas Страницы: 28

Бренд: ANEP Страницы: 48

Бренд: KYLAND Technology Страницы: 24

netHOST NHST-T100

Бренд: hilscher Страницы: 75

Бренд: ATI Technologies Страницы: 87

Бренд: Planet Страницы: 54

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

HiGain Line Unit HLU-388

Бренд: PairGain Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды