RS485/RS232 Port settings:
note:
Wireless control:
pay attention:
When connecting to RS232 or RS485, if there is any motion that cannot be controlled by the screen,
please adjust the two control lines.;
Wiring loop resistance is less than 20Ω;
Do not run in parallel with strong interference sources;
232 port setting: 2400, n, 8, 1 A data string should be
sent twice consecutively.
Code pairing / deleting (factory pairing is successful):
Long press the cycle button for 3 seconds, the screen is jogged once to enter the code-matching
state; within 10 seconds, the remote control up and stop buttons are also pressed, and the screen is
jogged again to complete the code-matching; the code deletion is the same as the code-matching
operation, odd times The operation is code pairing; even code deletion.
Code pairing / deleting (factory pairing is successful):
Long press the cycle button for 3 seconds, the screen is jogged once to enter the code-matching
state; within 10 seconds, the remote control up and stop buttons are also pressed, and the screen is
jogged again to complete the code-matching; the code deletion is the same as the code-matching
operation, odd times The operation is code pairing; even code deletion.
Intelligent electronic stroke positioning (this product can set the up and down stroke of the fabric
through the remote control)
Operation method:
Upward stroke setting: Positioning setting key (light on) → Up key → Up and down remote control
to the desired position → Stop → Positioning setting key (light off) → Upward travel record success
Downstroke setting: Positioning setting key (light on) → Down arrow key → Remote control up and
down to the desired position → Stop → Positioning setting key (light off) → Downstroke recorded
successfully
If it is really necessary to adjust the limit height due to the installation environment or site limitation,
you can use the motor positioning adjustment key to rotate the knob on the motor limiter; Just
remove the baffle at the power end to find the position of the motor
In order to ensure the accuracy and safety of the screen position, the screen must be raised and lowered
every half circle of the button to check whether the position is moved correctly! Be especially careful
when adjusting the height of the screen recovery. Excessive adjustment will cause the lower rod to jam
into the shell and cause serious consequences such as damage to the screen or falling of the lower rod!
Be careful when adjusting the unfolding height of the curtain. Always keep the curtain wrapped around
the rotating tube with 1.5 turns or more to ensure that the curtain will not fall.
Electrical parameters: voltage AC220~230V/50-60Hz, current 1.5A.
Green button
yellow button
Unfolding height (lower limit)
Retracted height (upper limit)
Motor
Counterclockwise：Up
Clockwise： Down
Counterclockwise： Down
Clockwise ：Up
Start Bits :1
Stop Bits : 1
Baud Rate :2400
Data Bits :8
UP: FFEEEEEEDD
STOP: FFEEEEEECC
DOW: FFEEEEEEEE
Some central controls need to
set the address code
FFEEEEEEAA
Learn address code instructions：FFXXXXXXAA
(XXXXXX is a hexadecimal character other than E and 5)
Hex Contro Code:
Press the up button, the screen will rise.
Press the stop button, the screen stop
Press the down button,the screen down.
connecting diagram
public line
S1 SW-PB
S2 SW-PB
S3 SW-PB
STOP
UP
DOWN
8P 8C
R S
-
232
P 1
8
7
6
5
4
3
2
1
1
6
2
7
3
8
4
9
5
R 4 5
J
Disassemble
the baffle
UP
STOP
DOWN
Wireless transmitter
Positioning
Settings Key
Adjusting method of fabric retracting (upper limit) and unfolding (lower limit):
USB Serial Port (COM3)
常规
端口设置 驱动程序 详细信息
事件
2400
8
无
位
/
秒(
B
):
数据位(
D
):
奇偶校验(
P
):
A
高级（
）
…
还原默认值(
R
)
1
无
停止位(
S
):
流控制(
F
):
取消
确定
Baud Rate:
2400
Data Bits:
8
Parity:
none
Stop Bits:
1
Flow Control:
Baud Rate:
Baud Rate
(
B
):
Data Bits
(
D
):
Parity
(
P
):
Stop Bits
(
S
):
A
advanced
（
）
…
Restore default
(
R
)
取消
确定
none
Flow Control
(
F
):
General Port Settings
Driver
Details
Event
