Grandstream Networks UCM6202 Скачать руководство пользователя

Страница: 23 / 32

P a g e

UCM Security Manual

•

TLS Self-Signed CA

This is used when UCM acts as a client, to authenticate the server. If the server the UCM connecting

to uses a self-signed certificate, you should have their certificate installed here so authenticity of

their certificate can be verified. If the server uses a certificate that is signed by one of the larger

CAs, you should install a copy of server CA certificate here.

•

TLS Cert

This is used when UCM acts as a server. It’s sent to the client during TLS handshake. The TLS

Cert should include the key and server certificate. The “common name” field in the server certificate

should match the server host (either IP or domain name). This is required if the client side is another

UCM (not a standard, some clients do not have this requirement for server authentication). If not

matching, authentication on the UCM (client) fails and the TLS connection cannot get established.

•

TLS Do Not Verify

This is effective when UCM acts as a client. If set to “Yes”, the server’s certificate (sent to the client

during TLS Handshake) won’t be verified. Considering if two UCMs are peered, since the default

certificate built in UCM at the factory has “common name” equaling “localhost” which is not a valid

IP address, authentication will fail for sure. So, this is the default setting to avoid authentication

failure when using default certificate. Please note skipping verification won’t have effect on

encrypting SIP messages. If set to “No”, UCM (client) will verify the server’s certificate using “TLS

Self-Signed CA”.

Please note that administrator also needs configure “SIP Transport” to be “TLS” on the SIP endpoint device
to encrypt SIP messages sent to the UCM.

Содержание UCM6202

































Результаты поиска

Содержание UCM6202

Отзывы:

Похожие инструкции для UCM6202

Бренды по названию

Популярные бренды

Grandstream Networks UCM6202, Руководство по безопасности

Результаты поиска

Содержание UCM6202

Отзывы:

Похожие инструкции для UCM6202

Бренды по названию

Популярные бренды