Grandio GRANDIO ELITE 8x12 2015 Скачать руководство пользователя страница 61

Страница: 61 / 72

INTERIOR ROOF SUPPORT ASSEMBLY

7.1

Attach the L08E-X to the upper roof section

as shown with S04/ML01 fasteners already in

place where the 607 meets the 601B, and the

609 and the 602B meet see , repeat this on

the front section of the greenhouse, and where

extensions meet at the AZ-1.

7.2

Attach the L08D-X to the rear lower roof

section where S04/ML01 fasteners are already

in place where the 609 and the 602B meet, and

the 609 and the 601B meet see , repeat on

the front section, and where the extensions

meet the AZ-1.

7.3

Attach the BZ-1’s to the roof line as shown

in diagram with the S04/ML01. The edge of

the BZ-1 should meet up to the edge of 609

exactly.

7.4

Use CZ-1’s to support the interior wall at

the eave using the S04/ML01. See diagram .

We suggest that you measure down 9” and mark

it with a pencil so the base of the CZ-1 will meet

there.

You may remove all stickers now with Goo
Gone remover if needed.

L08E-X

L08D-X

CZ-1

BZ-1

9”

L08D-X

L08E-X

BZ-1

CZ-1

602B

607

609

Roof
Vent

602B

601B

609

607

STEP SE

VEN

601B

Congratulations You Did It!!

Содержание GRANDIO ELITE 8x12 2015









































































Результаты поиска

Содержание GRANDIO ELITE 8x12 2015

Отзывы:

Похожие инструкции для GRANDIO ELITE 8x12 2015

Бренды по названию

Популярные бренды

Grandio GRANDIO ELITE 8x12 2015, Руководство пользователя

Результаты поиска

Содержание GRANDIO ELITE 8x12 2015

Отзывы:

Похожие инструкции для GRANDIO ELITE 8x12 2015

Бренды по названию

Популярные бренды