Grandio GRANDIO ELITE 8x12 2015 Скачать руководство пользователя страница 19

Страница: 19 / 72

2.4

Insert polycarbonate panels Y3-2 and

Y3-1 into place as shown in .

2.5

Attach 603E and 603D with W04

and S04/ML01 fasteners as shown in .

2.6

Attach the 603D to the 601B’s

using the W04-1’s with the S04/ML01

fasteners on both sides as shown in .

Y3-1

Y3-2

601B

603E

WG01

WG02

603D

W04

W04-1

S04

ML01

W04

603E

603D

W04-1

603D

601B

GRANDIO

T I P

BOLT INSTALLATION TIP:
Locate ML01/S04 nuts and

screws, loosely pre thread into the W04 and
W04-1’s and place in the groove of the
extrusion to make installation easier.

W04

W04-1

Inside View

STEP T

Transparent Film

Opal White Film

Polycarbonate

Panels

Sun

The UV-Protected side is covered with transparent film

and must face toward the sun. The side covered in white

film will always face the interior of the greenhouse. We

suggest you peel all film off completely prior to assem-

bly and use a permanent marker to place a small “X” on

the lower right corner of each panel on the transparent

side that faces the sun, each panel has a sticker labeling

the panel number and this side always faces the sun or

outward as well. DO NOT REMOVE LABELS UNTIL

YOU INSTALL PANELS. The “X” is suggested in case

you dis-assemble your greenhouse in the future so you

may identify which side has the UV coating. Always use

gloves when handling the polycarbonate panels as the

edges can be very sharp.

IMPORTANT: POLYCARBONATE PANELS

FRONT FRAME ASSEMBLY CONTINUED

ALWAYS ASSEMBLE FRONT HORIZONTAL

Содержание GRANDIO ELITE 8x12 2015









































































Результаты поиска

Содержание GRANDIO ELITE 8x12 2015

Отзывы:

Похожие инструкции для GRANDIO ELITE 8x12 2015

Бренды по названию

Популярные бренды

Grandio GRANDIO ELITE 8x12 2015, Руководство пользователя

Результаты поиска

Содержание GRANDIO ELITE 8x12 2015

Отзывы:

Похожие инструкции для GRANDIO ELITE 8x12 2015

Бренды по названию

Популярные бренды