Granby KLC-100 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 33

Granby KLC-100 Скачать руководство пользователя страница 14

13

5.0 BURNER INSTALLATION AND SPECIFICATIONS

5.1 ASSEMBLY & INSTALLATION OF BURNER

ASSEMBLY

Check that the burner model is correct for furnace rating required.
Assemble as per burner manufacturer’s instructions.

SELECT NOZZLE

Select oil input, nozzle and burner configuration as shown on furnace
operating decal.

INSTALL NOZZLE

Install selected nozzle, check for clean seating and tighten in nozzle
adaptor.

ELECTRODES

See burner manufacturer’s instructions for correct setting

INSERTION

MOUNT BURNER

Tighten top nut first so burner tips down
slightly. The burner is always installed in
an upright position by four (4) nuts.

PUMP BY-PASS

For one pipe system factory setting (no

PLUG

plug).

PRESSURE TUBE BF3 BURNER – 2 PIPES (IPEX) VENTING

THE PRESSURE TUBE MUST BE CONNECTED ON THE
APPROPRIATE LOCATION (TOP RIGHT) ON THE BURNER
CASING.

F3 BURNER – 1 PIPE (IPEX) VERTICAL VENTING
THE PRESSURE TUBE MUST BE CUT AT THE EXIT OF THE
ELECTRICAL  BOX. IT SHOULD MEASURE ATMOSPHERIC
PRESSURE.

WIRING

Refer to wiring diagram for correct burner
connections (see page 26).

THERMOSTAT

Connect the thermostat wires to the fan
timer control board (ST9103).

«
...
12
13
14
15
16
...
»

Содержание KLC-100


































Отзывы:

Нет отзывов