background image

2 8 3   R

E L E A S E

8–8

T

RIM

 T

ABS

Trim tabs are electrically and hydraulically operated. The trim tab system consist of a 

hydraulic pump, a two-rocker switch panel, a trim tab position indicator panel, and an auto-retract 
device. The rocker switch controls the pump which lowers and raises the trim tabs. The indicator 
panel keeps you constantly aware of the trim tab’s position. The auto-retract device causes the 
pump to raise the tabs every time the ignition switch is turned off

Trim tabs are used to regulate the attitude of the boat while moving. They are operated by a 

two-rocker switch panel and will aid in trimming the boat fore and aft for a smoother ride. Trim 
tabs can improve the ride of your boat by adjusting where the water is hitting the keel line. In a 
slight chop, the waves may be hitting the keel of your boat around the helm area causing an 
uncomfortable ride. By adjusting the trim tabs and lowering the bow, the waves will hit the keel at 
a more forward point and soften the ride. Experimenting with trim tabs in various sea conditions 
will help you determine the best positions for your boat under different load conditions.

Trim tabs are also useful in correcting a port or starboard running list. If the boat is listing to 

the port side, press the starboard trim tab switch toward “bow down”. Press the port trim tab 
switch toward “bow down” to correct a starboard list. This will tend to lower the bow by pulling 
the higher side to a level position. If your bow is already in a low position, you may correct a 
listing condition by pressing the trim tab switch toward “bow up”. This will cause the low side to 
rise and level the boat. The running angle will also gradually improve.

 The switches are marked “bow down” only. Trim tabs in the extreme “bow up” positions will 

have no effect on the boat's ride. Trim tabs in the extreme “bow down” position will cause the 
boat to come on plane with minimum bow rise. Unless you are operating at low speeds or with 
considerable cockpit weight you will likely want to raise the tabs slightly when underway to avoid 
“plowing” water. With the tabs in the “bow down” position, you will be able to maintain a plane at 
the least possible RPMs.

Trim Tab Pump Location

The trim tab pump is located in the console-rigging compartment. Hydraulic fluid levels 
should be checked on an annual basis or anytime there is evidence of a leak. 

N O T I C E

Most drive units are equipped with an adjustable rudder trim tab. This trim tab should be 
adjusted to balance the steering at the speed which you travel most frequently. Variations in 
speed, boat load, or changes in the drive unit trim will cause the steering to pull in one direction. If 
the boat pulls to the left, adjust the trim tab to the left and vice versa.

Содержание RELEASE 283

















































































Отзывы: